(12) months from the date of purchase by the end user. Zebra Technologies Corporation warrants the print head, under normal use and service, to be free from defects in material and work- manship for a period of ninety (90) days or 30KM of printing (whichever occurs first) from the date of purchase by the end user.
Page 4
THERMAL PRINTING: The print head becomes hot while printing. To protect from damaging the print head and risk of personal injury, avoid touching the print head. Use only the cleaning pen to perform maintenance. 980293-001 Rev. A...
The printer is a low cost, desktop direct thermal printer. The printer is specifically designed for printing labels, tags or continuous receipts (with or without bar codes) from any DOS™, Win- dows™or ASCII-based compatible host. 980293-001 Rev. A...
Step Attach Power Supply To The Printer Power OFF Check Voltage Plug in Power Module Plug in Power Cord Plug Power Cord into a Suitable AC Outlet See the SHOCK HAZARD WARNING on page 980293-001 Rev. A...
Page 11
The printer has either a parallel interface or a serial interface (with optional RJ-11 connector). Power OFF Parallel Interface RJ-11 Interface (Optional) Serial Interface For additional information on serial cable wir- ing, refer to Appendix A. 980293-001 Rev. A Installation and Operation...
Page 12
Installation and Operation Step Load Labels Power ON Open Cover Adjust Holders 1.0 inch 2.5 cm 1.5 inch 3.8 cm MOVIE MOVIE 980293-001 Rev. A...
Page 13
Load Labels - continued Install Roll Thread Through Guides Close Cover Tap Feed Button If the indicator remains dark, see Appendix A - Troubleshooting. 980293-001 Rev. A Installation and Operation...
Installation and Operation Step AutoSense Gap Sensor Adjustment Perform this procedure when loading a new roll. If your printer has the label dispenser option, turn OFF the label taken sensor. Power OFF Hold Feed Button Power ON MOVIE 980293-001 Rev. A...
Page 15
To Begin Normal Operation Note: Printer prints “out of DUMP” If the indicator remains orange or red, see the troubleshooting steps. 980293-001 Rev. A Installation and Operation 4 MO3351F 16 V3.21 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.9K avl...
Installation and Operation Label Dispenser Option MOVIE Open Door Use a Stylus to Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door 980293-001 Rev. A...
Installation and Operation Using Fan-Fold Media Open Guides to Width of Media Lock Guides in Place Insert Media Thread Media Through Guides 980293-001 Rev. A...
Page 18
Installation and Operation Step Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980293-001 Rev. A...
Printer appears to be working (media is being fed out), but nothing is printed. Printing is faded or poor quality. 980293-001 Rev. A Solution or Reason STATUS Indicator 1. Check power connections from A.C. outlet to power supply to printer.
Page 20
2. Possible problem with label stock. Use only Eltron approved labels and tags. 3. Possible label jam. 4. Insufficient memory for label size. Check the printer memory configuration. 5. Possible software problem. Refer to the EPL2 Programming manual. 980293-001 Rev. A...
The first troubleshooting reference source is the table on the previous page. Next, contact the Resources dealer where you purchased your printer. Zebra Technologies also provides a variety of information and user support services: 980293-001 Rev. A Appendix A - Troubleshooting Internet: http://www.eltron.com...
Re- Cable Wiring fer to the cash draw manufacturer's documenta- tion for proper drawer wiring. *+24 volts D.C. at no greater than 1.5 amps. 980293-001 Rev. A Appendix A - Troubleshooting RJ-11 PRINTER Pin No.
Pin No. STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 ACK/ BUSY PAPER ERR. READY INIT ERROR/ SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND 980293-001 Rev. A...
When you load new media, you can also clean the print head. Print Head Rub Cleaning Pen Across Dark Area of Print Head Wait One Minute Before Closing Printer Do Not Clean Roller 980293-001 Rev. A Appendix A - Troubleshooting MOVIE...
Always refer to the ELTRON part num- ber when placing an order. For the name of an Eltron brand dealer in your area, call: 1(805) 579-1800 or the nearest Zebra Technologies office (located on the back of this manual). Description Parallel Interface Cable, 6’...