Download  Print this page

Zebra Cameo User Manual

Mobile printer chargers
Hide thumbs

Advertisement

Mobile Printer
Chargers
User's Manual
MP Series, RP Series
Encore Series,
Cameo Series,
QL Series
Rev. F, July, 2002
Document: Chargers_F.pdf

Advertisement

Table of Contents
loading

  Related Manuals for Zebra Cameo

  Summary of Contents for Zebra Cameo

  • Page 1 Mobile Printer Chargers User’s Manual MP Series, RP Series Encore Series, Cameo Series, QL Series Rev. F, July, 2002 Document: Chargers_F.pdf...
  • Page 2: Liability Disclaimer

    No Liability for Consequential Damage In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation,...
  • Page 3: Table Of Contents

    Introduction ... 4 MP and RP Series Printers ... 4 Cameo and Encore Series ... 4 QL Series ... 4 Safety Warnings ... 4 UCLI72-4 Quad Charger ... 5 Description ... 5 Setting up the Charger ... 5 Charging Batteries ... 5 Charging Times ...
  • Page 4: Introduction

    This manual covers the use of all chargers currently of- fered by Zebra for use with MP, RP, Encore, Cameo and QL series mobile printers. MP and RP Series Printers The MP series (MP5022, MP5030, MP5033 and MP5044) and the RP3 use NiCad batteries, which require periodic “conditioning”...
  • Page 5: Ucli72-4 Quad Charger

    UCLI72-4 Quad Charger Description The UCLI72-4 Quad Charger is designed to charge up to four Lithium-Ion (LIon) QL series Mobile Printer battery packs simultaneously. The unit is supplied with an external 110/220 VAC power supply and a line cord compatible with its country of use.
  • Page 6 Note the orientation of the battery pack. Slide the battery pack into the charging bay until it stops. Then rock the battery pack back until it snaps into place. The amber indicator directly under the battery being charged will turn on if the battery is properly inserted.
  • Page 7 A.C. Cord Green Indicator 2: T IGURE Refer to the chart below for a quick reference: Amber Flashing Power Supply UCLI72-4 HARGER YSTEM Green Flashing O.K. (80% charged) Completely Charged Flashing Power Indicator Battery Status Charging Faulty Battery continued on next page UMAN-Charge...
  • Page 8: Charging Times

    Charging Times 80% charge Full Charge These times are for completely discharged batteries. Bat- tery packs which are still partially charged will take less time. The Quad Charger has a safety feature which stops charg- ing a battery after six hours regardless of its charge state. Safety Precautions Battery Safety Avoid accidental short circuiting of any battery.
  • Page 9: Ucn72-4 Quad Charger

    UCN72-4 Quad Charger Description The UCN72-4 Quad Charger is designed to charge up to four NiMH Encore and/or Cameo series batteries simulta- neously. Battery packs may be charged externally or while plugged into the printer. The unit has switch selectable 110/ 220 V.A.C.
  • Page 10: Ucn72-4 Part Numbers

    the battery pack to be charged. The charge indicator near the cable will either light steadily, or start to blink. On a fully charged battery, the indicator will go out after a few minutes, indicating a fully charged condition. On batteries in need of charging, the indicator will stop blinking after a period of time determined by the charge level of the battery and then stay lit continuously.
  • Page 11: Ncxx04 Series Quad Charger/Conditioners

    NCxx04 Series Quad Charger/Conditioners Description NC series Quad Chargers sequentially charge and/or condition up to 4 batteries. Charge time is approximately one hour per battery depending on battery’s state of charge. Condition cycle times vary with both the battery’s state of charge and with each model.
  • Page 12: Conditioning Battery Packs

    Conditioning Battery Packs In order to extend battery life, battery packs should be conditioned periodically. The NC series Quad Chargers are equipped with a "Condition" mode, which fully discharges a battery pack followed by a full charge cycle. Conditioning NiCad battery packs once a week is recommended for optimum performance of batteries.
  • Page 13: Ncxx04 Part Numbers

    The communications port should only be used by factory authorized personnel. NCxx04 Part Numbers Part Number* DC12127-1x DC12255-1x DC12363-1x DC12248-1x DC12464-2x DC12363-5x DC12363-6x * Last digit in part number Indicates model: -X0 = North American model -X1 = U.K. model -X2 = Continental European model -X3 = Australian model †...
  • Page 14: Li72 Wall Charger

    Description The LI72 is a wall mounted fast charger with universal 110 to 230, 50-60 Hz. VAC input. Multiple A.C. plug configura- tions comply with most interna- tional standards. This charger is used with the QL series printers (QL 220, QL 320, QL 420) equipped with Lithium Ion (LiIon) batteries.
  • Page 15: Li72 Models

    Do not attempt to charge batteries with the LI72 while printing. Attempting to print while charging can result in improp- erly charged batteries. LI72 Models Model number AT15759-1 AT15759-2 AT15759-3 AT15759-4 AT15759-6* *This model is suppled with an IEC socket to allow use as an in- line charger.
  • Page 16: Ucn72 Wall Charger

    110 to 230, 50-60 Hz. VAC input. Multiple A.C. plug configu- rations comply with most interna- tional standards. This charger is used with the Encore and Cameo series printers equipped with NiMH batteries. The UCN72 will charge a battery pack as fast as its...
  • Page 17: Ucn72 Models

    UCN72 Models Model number AT15244-1 AT15244-2 AT15244-3 AT15244-4 AT15244-6* *This model is suppled with an IEC socket to allow use as an in- line charger. Connection to A.C. supply is via a line cord configured with an A.C. plug for the country of intended use. Country of use U.S.
  • Page 18: Uc Series Charger/Conditioner

    The UC series of Charger/Conditioners is designed to charge and condition individual battery packs used on the MP, RP, Encore and Cameo series of portable printers. Battery packs may be charged off-unit or while connected to the printer. Typical charge time is 60 to 90 minutes.
  • Page 19: Uc Series Charger Models

    The “Condition” cycle on UC series chargers can also be used for this purpose. Used on MP5020/22 MP5030 MP5044 † Encore 2,3, Cameo † Encore 4 Charge Method Cable Cable Cable...
  • Page 20: Trickle Chargers

    NiCad battery packs such as Charger Body A.C. Receptacle Batt. Voltage/Model 7.2 V/ MP503x Series 6.0 V/ MP502x Series 12 V/ MP5044 6/7.2V/MP502x/3x Series 6/7.2V/Encore, Cameo Series 6-7.2V/MP Series 12V/MP5044 7.2V/Encore, Cameo used on the MP and RP series.
  • Page 21: Product Support

    Zebra Technologies Corporation 30 Plan Way Warwick, Rhode Island 02886.1012 USA Telephone: Fax: e-mail: Ask for the Help Desk In Europe: Zebra Technologies Europe, Ltd. Zebra House The Valley Centre, Gordon Road High Wycombe Buckinghamshire HP13 6EQ, United Kingdom Telephone: Fax: e-mail:...
  • Page 22 Visit our Website at www.zebra.com...