Related Manuals for Doka Framax stripping corner I Series
Summary of Contents for Doka Framax stripping corner I Series
- Page 1 999239002 07/2018 en-GB The Formwork Experts. Framax stripping corner I hydraulic 2017 models onward Original Operating Instructions Please retain for future reference © by Doka GmbH, A-3300 Amstetten 9239-200-01...
- Page 2 Original Operating Instructions Framax stripping corner I hydraulic Basic drawings of product Framax stripping cylinder I 9239-201-02 a ... Adjusting range between 342 mm and 438 mm b ... ø130 mm c ... SW 41 d ... 20 mm e ... 70 mm f ...
-
Page 3: Intended Use
Doka accepts no liability for products that ▪ have been altered! Hydraulic unit SCP V1200 50/60Hz with ▪ Repairs may be carried out only by Doka or - Coupling adapter Framax stripping cylinder I specialist companies authorised by Doka! (intended use) ▪... - Page 4 Original Operating Instructions Framax stripping corner I hydraulic Assembly NOTICE It is not permissible to install the adapter in the pushrod with only one pin D17.5 NOTICE ➤ ▪ Place the stripping cylinder on the centring stud of Stripping cylinders must always be fully the stripping corner.
- Page 5 Original Operating Instructions Framax stripping corner I hydraulic Adjustment of the Framax stripping CAUTION cylinder I Danger of crushing! ➤ No body parts or objects between hydraulic cylinder and assembly plate. Note: ➤ Installation of the hydraulics. In the initial position, the stripping cylinder must be fully ➤...
- Page 6 Original Operating Instructions Framax stripping corner I hydraulic Operation of the Framax stripping Dismantling corner I hydraulic ➤ Remove the Connecting pin 10cm. ➤ Retract the stripping cylinder. ➤ Start up the hydraulic unit. ➤ Switch off the hydraulic unit and disconnect the hydraulic hoses.
- Page 7 Original Operating Instructions Framax stripping corner I hydraulic 999239002 - 07/2018...
- Page 8 Original Operating Instructions Framax stripping corner I hydraulic Repositioning operation, Framax Mounting the Fixing unit for Framax stripping cylinder I stripping corner I ➤ Repositioning operation for stripping Remove the pegging tube from the fixing unit. ➤ ➤ Remove the Connecting pin 10cm. Place the spindle tube on the centring stud of the stripping corner.
-
Page 9: Practical Example
Original Operating Instructions Framax stripping corner I hydraulic Practical example Shaft with one Framax stripping cylinder I. 9239-216-01 Shown here with no guardrail system along the front A Framax stripping cylinder I B Framax stripping corner I C Hydraulic unit Framax V4 D Adapter for Framax stripping corner I Note: Alternatively, the shaft can be fitted with four Framax... -
Page 10: Technical Data
▪ Doka accepts no liability for products that have been altered! ▪ Repairs may be carried out only by Doka or specialist companies authorised by Doka! ▪ To avoid damage, the drive components must be stored in such a way that they are protected against direct climatic influences and aggressive substances. -
Page 11: Equipment Components
Equipment components A Pair of hydraulic hoses B Footplate As-delivered condition: ▪ Doka supplies the unit in ready-for-use condition. ➤ Temporarily stow pairs of hydraulic hoses that are - cleaned reservoir not in use in the parking positions inside the Hydrau- - clean hydraulic oil lic unit Framax V4. - Page 12 Original Operating Instructions Framax stripping corner I hydraulic Stripping the formwork: Note: NOTICE The couplings on the Hydraulic unit Framax V4 and the couplings on the pair of hydraulic hoses are colour- If there is not enough oil in the unit, attempting coded.
-
Page 13: Maintenance
Original Operating Instructions Framax stripping corner I hydraulic Maintenance Changing the oil Changing the drive CAUTION Risk of burns or scalds if an oil change is attempted while the hydraulic oil is still hot! Note: ➤ If the hydraulic unit has been in operation for The drive hexagon socket (width-across 8 mm) has to a lengthy period, allow the hydraulic oil to be replaced if it is damaged. - Page 14 Original Operating Instructions Framax stripping corner I hydraulic Hydraulic unit Xclimb 60 V45 50/60Hz NOTICE Invariably, only one stripping cylinder can be connected to and operated with the Hydraulic unit Xclimb 60 V45 50/60Hz! Exception: ▪ No-one in the danger zone! ▪...
- Page 15 Original Operating Instructions Framax stripping corner I hydraulic Hydraulic unit SCP V1200 50/60Hz NOTICE Invariably, only one stripping cylinder can be operated with the Hydraulic unit SCP V1200 50/60Hz! Exception: ▪ No-one in the danger zone! ▪ Formwork erecting and stripping operations are under observation at all times! Note: The couplings on the coupling adapter and the cou-...
- Page 16 EN 982 1996+A1:2008 Person authorised to compile technical documentation (pursuant to European Directive on Machinery Annex II): Dipl.-Ing. Ludwig Pekarek Josef Umdasch Platz 1 A-3300 Amstetten Doka GmbH Amstetten, 14/06/2018 Josef Umdasch Platz 1 A-3300 Amstetten Dipl.-Ing. Peter Reisinger Dipl.-Ing. Ludwig Pekarek...
- Page 17 Original Operating Instructions Framax stripping corner I hydraulic Component overview [kg] Article n° [kg] Article n° Component overview [kg] Article n° Framax stripping corner I 2.70m 171.0 588675000 Hydraulic unit Xclimb 60 V45 50/60Hz 321.0 581322000 Framax stripping corner I 1.35m 90.0 588614000 Hydraulikaggregat Xclimb 60 V45 50/60Hz Framax stripping corner I 3.30m...
- Page 18 70 countries, the Doka Group has a highly efficient dis- than 6000. tribution network which ensures that equipment and Doka GmbH | Josef Umdasch Platz 1 | 3300 Amstetten | Austria | T +43 7472 605-0 | F +43 7472 66430 | info@doka.com | www.doka.com 999239002 - 07/2018...
Need help?
Do you have a question about the Framax stripping corner I Series and is the answer not in the manual?
Questions and answers