Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Zanussi ZUD 9100 F
Summary of Contents for Zanussi ZUD 9100 F
- Page 1 FREEZER ZUD 9100 F INSTRUCTION BOOKLET 2222740-62...
-
Page 2: Table Of Contents
Maintenance and Cleaning Internal cleaning Periodic cleaning When the appliance is not in use Something Not Working? Service and Spare Parts Customer Care Department Zanussi Service Force Guarantee Conditions Instructions for the Installer Technical Specifications Installation Positioning Electrical Connection Building-in Instructions... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation Check the appliance for transport damage. -
Page 4: Description Of The Appliance
When unplugging always pull the plug from the mains socket, do not pull on the cable. Servicing This product should be serviced by an authorised engineer and only genuine spare parts should be used. Under no circumstances should you attempt to repair the appliance yourself. -
Page 5: Operation
OPERATION Before use Remove all securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5 ml to 0.5 litre of water). Do not use soap or deter- gent as the smell may linger. Dry thoroughly. Freezer controls Thermostat control knob Push button ON/OFF Pilot light... -
Page 6: Open Door Acoustic Alarm
on. This signal can be temporarily stopped by depressing the push button for fast-freezing The fast-freezing push button can be released as soon as the warning light is off. Open door acoustic alarm This appliance also incorporates an alarm which sounds if the door is left open for more than 60 sec- onds. -
Page 7: Health And Safety Guidelines
HEALTH AND SAFETY GUIDELINES Because of consumer demand, preservatives have been removed from many pre-prepared foods. This together with the changes in shopping habits to a once-a-week shop, mean that safe handling and storage of food is even more important than ever. The following tips should help you to ensure that the food in your home is in as perfect condition as possible. -
Page 8: Defrosting
DEFROSTING The freezer compartment will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thick- ness of the frost exceeds 1/4". During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out and it is advisable to carry out this operation when... -
Page 9: Maintenance And Cleaning
MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELEC- TRICITY supply. Warning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. -
Page 10: Something Not Working
SOMETHING NOT WORKING? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom No power to the appliance The temperature in the freezer is too high... -
Page 11: Service And Spare Parts
CUSTOMER CARE DEPARTMENT For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you are invited to contact our Customer Care Department by letter or telephone or visit our website at www.zanussi.co.uk... -
Page 14: Guarantee Conditions
Standard guarantee conditions We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part there- of is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. -
Page 15: Technical Specifications
TECHNICAL SPECIFICATIONS DIMENSIONS POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED AVERAGE DAILY UNITS ELECTRICITY(*) GROSS CAPACITY NET CAPACITY STAR RATING (*)This figure is based on standard test results in accordance with European Standard EN153. Actual con- sumption will depend on how the appliance is used and where it is located. INSTALLATION Positioning This appliance should only be installed at a location... -
Page 16: Electrical Connection
The cover/carrier is indicated by the coloured insert at the base of the plug. A replacement cover/carrier must be obtained from your local Zanussi Service Force Centre. This appliance complies with the E.E.C. Directive No. 87/308 of 2.6.87 relative to radio interference suppression. -
Page 17: Building-In Instructions
BUILDING-IN INSTRUCTIONS Before carrying out any work, remove the plug from the power socket. Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure). -
Page 18: Building In The Appliance Under A Worktop
Attention After completion of the door reversing opera- tion, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fit- ting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting. - Page 19 3. Two cabinet securing brackets are supplied with the installation pack. They need to be assembled onto the cabinet prior to cabinet being pushed into the Kitchen aperture. - To fit these brackets remove the two screws at the top left and right hand front corners of the cabinet. - Position the two brackets as shown in the figure and replace the two securing screws.
- Page 20 7. Screw appliance into place and retain the cabinet with screws through the securing brackets into the worktop or adjacent woodwork as necessary. 8. To mount the furniture door proceed as shown in the figures: clic clic...
- Page 21 UPPER PART OF KITCHEN FURNITURE PANEL LOWER PART OF KITCHEN FURNITURE PANEL...
-
Page 22: Fitting The Plinth
9. Refit the covering strip. Fitting the plinth Important For the efficient operation of the appliance, it is important that the original ventilation grid is used. For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. - Page 24 © Electrolux Household Appliances Limited 2000...