Care And Cleaning - Kenwood FP670 Series Manual

Hide thumbs Also See for FP670 Series:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
Hints:-
For best results do not fill the glass jar more than half full with ingredients to be blended.
Blend small quantities of cooked ingredients together with a little gravy or milk to make baby food.
Best results are obtained using a high speed.
When milling herbs, best results are obtained when the herbs are clean and dry.
IMPORTANT
You can ensure the long life of your Multi Mill by switching off promptly as soon as the desired fineness has been reached.
Maximum continuous operation for any process must not exceed 2 minutes.
Do not leave your Multi Mill unattended whilst in operation.
When milling dried ginger, it should be broken into pieces before milling, whilst Turmeric is extremely hard and considered unsuitable for
milling.
WARNING
NEVER PLACE THE BASE AND BLADE ASSEMBLY ONTO THE APPLIANCE WITHOUT THE JAR IN POSITION, NOR DISMANTLE
BEFORE REMOVING THE COMPLETE MULTI MILL FROM THE PROCESSOR. UNDER NO CIRCUMSTANCES MUST THE MULTI MILL
JAR BE USED IN CONJUNCTION WITH THE LIQUIDISER BASE A989, A990, A993, A996
YOUR MULTI MILL IS UNSUITABLE FOR PROCESSING HOT LIQUIDS.
Maximum Operating Capacities for Your Food Processor
Shortcrust Pastry up to a flour weight of ................................................................................................ 12oz/340g
Yeast dough up to a flour weight of .................................................................................................... 1lb 2oz/500g
Cake mix ingredients totalling not more than ......................................................................................... 3lb/1.36Kg
Chopping meat ....................................................................................................................................... 12oz/340g
Liquid capacity - bowl with maxi-blend canopy ................................................................................. 2.25pt/1.3litre
Liquidiser .............................................................................................................................................. 1.75pt/1litre
Paddle egg whisk ................................................................................................................................ 6 egg whites
Twin beater geared whisk ................................................................................................................... 4 egg whites

Care and Cleaning

Before cleaning always switch off and remove the plug from the power supply.
Immediately after use, wash all pieces except the power unit, twin beater geared whisk, liquidiser goblet and base, multi-mill base, blade and
housing assembly in hot soapy water, then dry thoroughly. Take care when washing the steel blade and cutting plates - they are extremely
sharp. You may place the following components in a dishwasher; bowl, lid, pushers, steel blade, maxi-blend canopy, dough tool, paddle egg
whisk, citrus juicer, centrifugal juicer, multi-mill jar, storage box and processing plates. However, please ensure that they are only placed on
the top rack of the dishwasher.
Wipe over the power unit of your Food Processor with a damp cloth and polish with a dry one. Ensure that the safety interlock is clear of food
debris.
Always store the food processor with its dust cover if supplied, in place.
Twin Beater Geared Whisk
Detach each whisk from the drive head of the whisk assembly by gently pulling free. Wash the whisks in warm water. Wipe the drive head with
DO NOT IMMERSE THE DRIVE HEAD IN WATER.
a damp cloth then dry.
Liquidiser
Half fill with warm water and place onto the food processor. With the lid and filler cap in place, switch on for 20-30 seconds to dislodge any
particles of food. Empty out the water and rinse with clean warm water. Wipe off any surplus liquid and leave in a warm atmosphere to dry.
Take care when drying by hand as the blades are sharp.
Do not immerse the liquidiser base in water.
Multi-mill
Wash the blade assembly in hot soapy water, rinse and dry well. Take care when handling the blades as they are very sharp. Do not leave the
blade assembly soaking in water.
Service
If the cord is damaged it must, for safety reasons, be replaced by KENWOOD or an authorised KENWOOD repairer.
Contact the dealer from whom you purchased your appliance.
11

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents