Introduction; Before Applying Pow Er; Safety Precautions - Kenwood CD-224M Instruction Manual

Introduction

Before applying pow er

2
Units are designed for operation as follow s.
U.S.A. and Canada .................................. AC 120 V only
Australia .................................................. AC 240 V only
* AC voltage selection
The AC voltage selector sw itch on the rear panel is set to the voltage
that prevails in the area to w hich the unit is shipped.
connecting the pow er cord to your AC outlet, make sure that the
setting position of this sw itch matches your line voltage. If not, it must
be set to your voltage in accordance w ith the follow ing direction.
Note:
Our w arranty does not cover damage caused by excessive line
voltage due to improper setting of the AC voltage selector sw itch.
For the United Kingdom
1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted w hen replacing the fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the pow er points in your home or the cable is too short to reach
a pow er point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer.
If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent
connection to the mains supply.
IM PORTANT
The w ires in the mains lead are coloured in accordance w ith the follow ing code:
Blue : Neutral
Brow n : Live
Do not connect those leads to the earth terminal of a three-pin plug.

Safety precautions

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REQUIREM ENT BY NEDERLAND GAZETTE
Batteries are supplied w ith this product. When
they empty, you should not throw aw ay. In-
stead, hand them in as small chemical w aste.
Downloaded from: http://www.usersmanualguide.com/
Factory fitted moulded mains plug
APPLIANCE TO RAIN OR M OISTURE.
THE LIGHTNING FLASH WITH ARROWHEAD SYM BOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE
USER TO THE PRESENCE OF UNINSULATED " DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT M AY
BE OF SUFFICIENT M AGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAM ATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IM PORTANT OPERATING AND M AINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOM PANYING
THE APPLIANCE.
Caution : Read this section carefully to ensure safe operation.
Europe and U.K. ............................................... AC 230 V only
* Other countries ............. AC 110-120 / 220-240 V sw itchable
AC voltage selector sw itch
Before
Caution : Read this section carefully to ensure safe operation.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REM OVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL.
The marking is located on the rear panel and says that the component
uses laser beams that have been classified as Class 1. It means that
the unit is utilizing laser beams that are of a w eaker class. There is no
danger of hazardous radiation outside the unit.
AC1 1 0 –
1 2 0 V
OUTPUT SYSTEM DIGITAL
CON TROL OUT
L
SL1 6 XS 8
R
OPTICAL
AC1 1 0 – AC2 2 0 –
1 2 0 V 2 4 0 V
M ove sw itch lever to match your line voltage w ith a
small screw driver or other pointed tool.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
Introduction
CD-2 2 4 M / DPF-J5 0 1 0 (En)
AC2 2 0 –
2 4 0 V