Table of Contents
Advertisement
RX- V493RDS
RX- V393RDS
Natural Sound AV Receiver
Récepteur audiovisuel "Son Naturel"
Natural Sound AV-Receiver
Natural Sound AV-receiver
Sintonizzatore AV a suono naturale
Receptor AV de Sonido Natural
Natural Sound AV Ontvanger
BEDIENUNGSANLEITUNG
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
OWNER'S MANUAL
MODE D'EMPLOI
BRUKSANVISNING
G B
Advertisement
Table of Contents
Related Manuals for Yamaha RX-V393RDS
Summary of Contents for Yamaha RX-V393RDS
- Page 1 RX- V493RDS RX- V393RDS Natural Sound AV Receiver Récepteur audiovisuel “Son Naturel” Natural Sound AV-Receiver Natural Sound AV-receiver Sintonizzatore AV a suono naturale Receptor AV de Sonido Natural Natural Sound AV Ontvanger OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING...
-
Page 2: Supplied Accessories
Batteries (size AA, R6, UM-3) Piles (taille AA, R6, UM-3) Batterien (Größe AA, R6, UM-3) Batterier (storlek AA, R6, UM-3) Batterie (dimensioni AA, R6, UM-3) Pilas (tamaño AA, R6, UM-3) Batterijen (maat AA, R6, UM-3) RX-V393RDS DELAY/CENTER /REAR/SWFR TEST EFFECT – DELAY TIME... -
Page 3: Table Of Contents
Thank you for selecting this YAMAHA AV receiver. 5 Speaker Configuration (Power Amp. Section) RX-V493RDS Main: 65W + 65W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz Center: 65W (8Ω) RMS Output Power, 0.04% THD, 1 kHz Rear: 20W + 20W (8Ω) RMS Output Power, 0.04% THD, 1 kHz... -
Page 4: Caution
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. -
Page 5: Notes About The Remote Control Transmitter
DUAL:4 MIN. /SPEAKER MAIN A OR B:8 MIN. /SPEAKER A B:16 MIN. /SPEAKER Remote control transmitter operation range RX-V493RDS RX-V393RDS –dB Remote control sensor Notes There should be no large obstacles between the remote control transmitter and the main unit. -
Page 6: Profile Of This Unit
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on. -
Page 7: Speaker Setup
SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker Configuration”... -
Page 8: Connections
L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * If you have YAMAHA components numbered as to connect the output (or input) terminals of each component to the same-numbered terminals of this unit. - Page 9 RX-V393RDS Monitor TV Turntable VIDEO UNBAL. MAIN MONITOR OUT VIDEO PHONO TAPE VIDEO TAPE 10dB MAIN LEVEL Tape deck, MD recorder, etc. AC OUTLETS (SWITCHED) (Europe model) ... 2 SWITCHED OUTLETS (U.K. model) ... 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit.
- Page 10 Connecting with 6 channel discrete outputs of a Dolby digital (AC-3) decoder or a DVD player, etc. If you have a Dolby Digital (AC-3) decoder or a DVD player etc. which incorporates a Dolby Digital (AC-3) decoder or a DTS decoder, its 6 channel discrete outputs can be connected to the 6CH DISCRETE INPUT terminals of this unit.
- Page 11 TAPE TAPE 10dB MAIN LEVEL Notes for RX-V393RDS • The laserdisc player (or another unit) must be also connected to the VIDEO AUDIO SIGNAL input terminals of this unit for playing a source with the Dolby Pro Logic Surround decoded or in normal stereo (or monaural).
-
Page 12: Connecting Speakers
Connect the SUBWOOFER OUTPUT terminal of this unit to the INPUT terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. - Page 13 How to Connect: Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed.
-
Page 14: Impedance Selector Switch
OUTPUT terminals (for driving speakers with external amplifiers) OUTPUT REAR CENTER (SURROUND) WOOFER CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal. -
Page 15: Antenna Connections
ANTENNA CONNECTIONS Each antenna should be connected to the designated terminals correctly, referring to the following diagram. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. -
Page 16: Controls And Their Functions
CONTROLS AND THEIR FUNCTIONS FRONT PANEL RX-V493RDS NATURAL SOUND AV RECEIVER STANDBY/ON A/B/C/D/E PHONES SPEAKERS RX-V393RDS NATURAL SOUND AV RECEIVER STANDBY/ON A/B/C/D/E PHONES SPEAKERS CINEMA DSP RX–V493RDS BASS TREBLE BALANCE RDS MODE/FREQ EON DEF G CINEMA DSP RX–V393RDS BASS TREBLE... - Page 17 6CH DISCRETE INPUT DVD/LD TV/DBS terminals of this unit are selected as the input signals. RX-V393RDS only When the VIDEO input source is selected, pressing the same button (VIDEO) switches the input signals between 2 channel stereo signals and 6 channel discrete signals.
- Page 18 Selects a center channel output mode (NORMAL, WIDE or PHANTOM). (For details, refer to page 23.) PROGRAM selector button RX-V393RDS only When the built-in digital sound field processor (including the Dolby Pro Logic Surround decoder) is on, this button changes the currently selected DSP program whenever the right or left side of this button is pressed.
-
Page 19: Display Panel
DISPLAY PANEL PRESET MEMORY AUTO PTY HOLD Multi-information display Displays various information, for example station frequency, preset station number and name of selected input source. STEREO indicator Lights up when an FM stereo broadcast with sufficient signal strength is received. Signal-level meter Indicates the signal level of the received station. -
Page 20: Remote Control Transmitter
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. - Page 21 TIME/LEVEL +/– key. (For details, refer to page 28, 40 and 41.) DELAY TIME +/– key RX-V393RDS only Adjusts the delay time, or the time difference between the begining of source sound and the begining of effect sound.
-
Page 22: Speaker Balance Adjustment
Select the main speakers to be used. SPEAKERS * If you use two main speaker systems, press both the A and B switches. BASS TREBLE Set to the “0” position. TEST RX-V393RDS TEST EFFECT ON/OFF PROLOGIC ENHANCED VIDEO /6CH PLAY... - Page 23 The test tone from the left rear speaker and the right rear speaker will be heard at the same time. Adjust the BALANCE control so that the effect sound output level of the left main speaker and the right main speaker are the same. RX-V393RDS DELAY/CENTER – DELAY TIME TEST...
- Page 24 DELAY/CENTER /REAR/SWFR b) Adjust its level. * Pressing the + side raises and the – side lowers the level. TIME/ – LEVEL RX-V393RDS CENTER LEVEL RX-V393RDS REAR LEVEL – DELAY TIME PROGRAM DIR A DIR B –dB...
-
Page 25: Basic Operations
From page 25 to 41, this manual describes how to operate this unit mainly by using the front panel control parts. To operate this unit on the remote control transmitter, use the corresponding keys on the remote control transmitter. TO PLAY A SOURCE VOLUME –dB ∞... - Page 26 RX-V493RDS TV/DBS DVD/LD TAPE/MD MON 2CH/6CH RX-V393RDS VIDEO 2CH/6CH To cancel listening to a decoded source using Dolby Digital (AC-3) or DTS Press the same button again or select another input source. Note for reproducing discrete signals with Dolby Digital (AC-3) or DTS decoded: 1.
-
Page 27: To Record A Source To Tape (Or Md)
(For detailed information on the tuning operations, refer to the page 29.) VOLUME –dB RX-V393RDS –dB Begin recording on the tape deck (or MD recorder etc.) or VCR connected to this unit. If the tape deck (or MD recorder etc.) is used for... -
Page 28: Adjusting The Subwoofer Output Level
Selecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. SPEAKERS Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. -
Page 29: Tuning Operations
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). AUTOMATIC TUNING Select “TUNER”... -
Page 30: Preset Tuning
MANUAL PRESET TUNING This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 groups) can be stored. To store stations Tune to a desired station. - Page 31 AUTOMATIC PRESET TUNING You can also make use of an automatic preset tuning function for RDS stations only. By this function, this unit performs automatic tuning and stores RDS stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 30.
-
Page 32: Exchanging Preset Stations
EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. Example) If you want to shift the preset station on E1 to A5, and vice versa. Recall the preset station on E1 (by following the method of “To recall a preset station”... -
Page 33: Receiving Rds Stations
In areas where RDS broadcasts cannot be received, the RDS broadcast functions do not operate. (The procedures from page 33 to page 37 are not necessary.) RECEIVING RDS STATIONS RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal. - Page 34 Program types in the PTY mode NEWS News: Short accounts of facts, events and publicly expressed views, reportage and actuality. AFFAIRS Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis. INFO Information: Program whose purpose is to impart advice...
-
Page 35: Changing The Rds Modes
Changing the RDS modes When an RDS station is received, “PS”, “PTY”, “RT” and/or “CT” that correspond to the RDS data services employed by the station light up on the display. By pressing the RDS MODE/FREQ button once or more, you can change the display mode among the RDS modes employed by the received station in the order shown below. - Page 36 Calling a program of your desired program type from among preset RDS stations (PTY SEEK) By designating a program type, the unit automatically searches all preset stations for an RDS station which broadcasts a program of that program type. * There are 15 program types to classify RDS stations. For details, refer to page 34. Turn the unit into the PTY SEEK mode.
- Page 37 Making this unit call a program of your desired program type automatically This function uses the EON (Enhanced Other Networks) data service on the RDS station network. By only selecting a desired program type (NEWS, INFO, AFFAIRS or SPORT), this unit automatically searches all preset RDS stations for a station that broadcasts a program of that program type in the background, and, if found, receives a program when its broadcast starts in place of the program now being received.
-
Page 38: Using Digital Sound Field Processor (Dsp)
Dolby Surround. The operation of the Dolby Pro Logic Surround decoder can be controlled by selecting a corresponding DSP program including a combined operation of the Yamaha DSP and the Dolby Pro Logic Surround. Brief Overview of Digital Sound Field Programs The following list gives you a brief description of the sound fields produced by each of the DSP programs. - Page 39 Follow steps 1 – 6 shown in “BASIC OPERATIONS” on page 25. Select the desired program that is suitable for the source. RX-V493RDS RX-V393RDS PRO LOGIC ENHANCED Turn the DSP on so that a program name lights up on the display.
-
Page 40: Adjustment Of The Center Level
Once the output level is adjusted, the level value will be the same in all the digital sound field programs mentioned above. RX-V393RDS Note This adjustment is useful only when the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected. -
Page 41: Adjustment Of Delay Time
Note Adding too much delay will cause an unnatural effect with some sources. RX-V393RDS only The value of the delay time you set the last time will remain memorized even when this unit is in the standby mode. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. -
Page 42: Setting The Sleep Timer
SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can make this unit turn into the standby mode. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is helpful. Notes The SLEEP timer can be controlled only with the remote control transmitter. -
Page 43: Troubleshooting
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM... -
Page 44: Specifications
Minimum RMS Output Power per Channel (Power Amp. Section) Main L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD < > RX-V493RDS ...65W+65W < > RX-V393RDS ...50W+50W Center 8 ohms, 1 kHz, 0.04% THD < > RX-V493RDS ...65W <... - Page 45 (Input Shorted, 1 kHz) ...60 dB or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR (Input 5.1 k-ohms Shorted, 1 kHz) ...60 dB or more < > RX-V393RDS PHONO MM (Input Shorted, 1 kHz) ...60 dB or more CD/TAPE·MD/VIDEO/VCR (Input 5.1 k-ohms Shorted, 1 kHz) ...60 dB or more...
- Page 46 YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA AM GEDEELTE Afstembereik ...531 tot 1.611 kHz...