Troubleshooting; Maintenance; Drilling In Wood; Drilling In Metal/Masonry - Black & Decker BCD700S Original Instructions Manual

English
(original instructions)
● Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
● Secure and maintain work area, as instructed in the
Safety Instructions.
● Run the drill very slowly, using light pressure, until
the hole is started enough to keep the drill bit from slipping
out of it.
● Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
● Hold the drill firmly with two hands to control its
twisting action.
● DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
● Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
● Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
● Make sure switch turns drill on and off.

Drilling in wood

Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The
cutting lubricants that work best are sulfurized cutting oil or
lard oil.
Drilling in masonry
For drilling in masonry, set the collar (3) to the hammer
drilling position by aligning the symbol with the marking.
Slide the speed selector (5) towards the front of the tool
(2nd gear).
Screwdriving
● Always use the correct type and size of screwdriver bit.
● If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
● Always hold the tool and screwdriver bit in a straight line
with the screw

Troubleshooting

Problem Possible cause
Unit will not start. Battery pack
not charged.
Battery pack will Charger not
not charge. plugged in.
Surrounding air
temperature too hot or
too cold.
8

Maintenance

Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Protecting the environment
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
Possible solution
Check battery pack
charging requirements
Plug charger into a
working outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Problem Possible cause
Unit shuts Battery pack has
off abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
● Regularly open the chuck and tap it to remove any dust
from the interior.
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Voltage V
DC
No-load speed Min
-1
Max. torque Nm
Chuck capacity
mm
Max Drilling capacity
/
mm
Steel/wood Ma-
sonary
Weight
kg
Charger
Input voltage V
AC
Output voltage V
DC
Possible solution
Allow battery pack to
cool down.
Place on charger
and allow to charge.
BCD700S
18
0-360/0-1400
17.5/40
1-10
/
10/25 10
0.90 (with battery 1.30)
906214**
230
18