Features; Vibration - Black & Decker BCD700S Original Instructions Manual

Hide thumbs Also See for BCD700S:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
English
(original instructions)
● Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
● Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
Safety of others
● This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety.
● Children should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
● Injuries caused by touching any rotating/moving parts.
● Injuries caused when changing any parts, blades
or accessories.
● Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
● Impairment of hearing.
● Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by EN
60745 and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
6
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers (Not provided with the tool)
Batteries
● Never attempt to open for any reason.
● Do not expose the battery to water.
● Do not store in locations where the temperature may
exceed 40 °C.
● Charge only at ambient temperatures between 10 °C and
40 °C.
● Charge only using the charger provided with the tool.
● When disposing of batteries, follow the instructions given
p
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
● Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
● Never attempt to charge non-rechargeable batteries.
● Have defective cords replaced immediately.
● Do not expose the charger to water.
● Do not open the charger.
$
● Do not probe the charger.
The charger is intended for indoor use only.
+
Read the instruction manual before use.
#
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
● If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. Dual range gearing
6. Battery (x2 with BCD700S2S)

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents