Yamaha EMX62M Owner's Manual

Yamaha EMX62M Owner's Manual

Yamaha musical instrument owner's manual emx62m
Hide thumbs Also See for EMX62M:

Advertisement

Owner's Manual
E
Keep This Manual For Future Reference.

Advertisement

Table of Contents
loading

Summary of Contents for Yamaha EMX62M

  • Page 1 Owner’s Manual Keep This Manual For Future Reference.
  • Page 2: Main Section

    The Owner’s Manual Revisions Thank you for purchasing the Yamaha EMX62M Powered Mixer. Parts of the EMX62M owner’s manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner’s manual. P.11 ■ MAIN section...
  • Page 3 ■ Block & Level Diagrams 8kHz 4kHz 2kHz 1kHz 500Hz 250Hz 125Hz MONITOR EFFECT MAIN HIGH HIGH M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2002 Yamaha Corporation HIGH EFFECT DIGITAL...
  • Page 4 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA 90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
  • Page 5 If noise occurs, use the telephone away from the unit. Volume level setting • Do not set all equalizer controls and faders to maximum. Doing so may cause oscillation depending on the condition of the connected unit and speakers, and may damage the speakers. Precautions EMX62M—Owner’s Manual...
  • Page 6 Precautions EMX62M—Owner’s Manual...
  • Page 7: Table Of Contents

    Introduction Thank you for purchasing the Yamaha EMX62M Powered Mixer. In order to take full advantage of the EMX62M and enjoy long and trouble-free operation, read this owner’s manual carefully, and keep it in a safe place for future reference.
  • Page 8: Emx62M Quick Guide

    SPEAKERS 1 and 2 jack on the rear panel of the EMX62M. EMX62M • The EMX62M is a monaural mixer. The same signal will be output from all SPEAKERS jacks on the rear panel. You do not need to differentiate right from left speakers.
  • Page 9 Z jack of a channel, you cannot connect the effect unit to the Hi-Z jack of the channel. Connecting an electronic musical instrument To the EMX62M’s LINE jacks, you can connect an electronic musical instrument such as a syn- thesizer, drum machine, signal processor con- nected to an electric guitar, etc.
  • Page 10 EMX62M STEP 5 Power off 1 Press the POWER switch of the EMX62M to turn off the power to the unit. 2 Turn off the power to all connected devices. • Be sure to follow the power off sequence specified above to prevent the speakers from being damaged.
  • Page 11: Front & Rear Panels

    PAD switch (1–4 only) The PAD switch attenuates the input signal by 30 dB. When connecting a line-level source to inputs 1 through 4, or if a microphone signal is distorted, use the PAD switch to attenuate the input signal. EMX62M—Owner’s Manual...
  • Page 12: Digital Effect Section

    The effects processor can also be turned on and off remotely by connecting an optional foot- switch to the FOOT SW jack. EMX62M—Owner’s Manual MAIN Section The MAIN section is used to set the MAIN MAS- TER level, 7-band graphic equalizer, AUX IN and 2TR IN levels, and MAIN EFFECT RTN level.
  • Page 13: Monitor Section

    Power switch and indicator Power ON/OFF switch and indicator This switch turns the power of the EMX62M on/ off. When the switch is turned on, the indicator lights up. Note: Before turning the EMX62M on/off, turn down the MASTER controls of the MONITOR and MAIN section.
  • Page 14: Input/Output Panel

    FOOT SW jack The FOOT SW jack is used to connect an optional footswitch, such as the Yamaha FC5, which can be used to turn the built-in digital effects processor on and off. The DIGITAL EFFECT ON switch must be in the ON position in order to use the footswitch.
  • Page 15 PHONES—OUTPUT jack The PHONES—OUTPUT phone jack outputs the MAIN bus signal after the 7-band graphic equalizer and MASTER level control, and can be connected to a pair of stereo headphones for per- sonal monitoring. Front & Rear Panels EMX62M—Owner’s Manual...
  • Page 16: Rear Panel

    EMX62M—Owner’s Manual Installation The EMX62M uses a forced cooling system with intake on the bottom of the rear panel and exhaust on the top of the rear panel to avoid blocking the heated air flow.
  • Page 17: Hookup Example

    EMX62M, in practice, only one effects processor, internal or external, will be used at a time, so the footswitch is not required when using external effects.
  • Page 18: Basic Operation

    Basic Operation Connecting Sources Before connecting any microphones or instru- ments, make sure that the EMX62M and any other applicable equipment is turned off. Also make sure that the LEVEL control on each EMX62M input channel, and the MAIN MAS- TER and MONITOR MASTER controls are turned down.
  • Page 19: Installing An Optional Rack Mount Kit

    Installing an optional rack mount kit You can rack-mount the EMX62M using an optional rack mount kit (RK-88). Rack mount kit RK-88 • Bracket 2 • Screw 6 Before you rack-mount the EMX62M, make sure that sufficient ventilation will be maintained.
  • Page 20: Troubleshooting

    The device may have malfunctioned. Please contact your dealer. Turn off the power to the EMX62M, or lower the volume level. The EMX62M will return to its normal operation in several seconds. Then, turn on the power to the unit or raise the volume level and check to see if the high range is audible.
  • Page 21: Specifications

    Master level control: nominal level 1 channel level control: nominal level All channel level controls: minimum 1 channel level control: nominal level 10 kHz shelving * 100 Hz shelving * 230 V AC 50 Hz 240 V AC 50 Hz Specifications EMX62M—Owner’s Manual...
  • Page 22: Output Specifications

    PHONES OUT REC OUT (1, 2) • PHONE JACKS are unbalanced. • 0 dB= 0.775 Vrms, 0 dBV= 1 Vrms. Dimensions Specifications are subject to change without prior notice. EMX62M—Owner’s Manual Nominal impedance Sensitivity Nominal level 50–600 Mics –62 dB (0.616 mV) –50 dB (2.45 mV)
  • Page 23: Block & Level Diagrams

    Block & Level Diagrams 8kHz 4kHz 2kHz 1kHz 500Hz 250Hz 125Hz MONITOR EFFECT MAIN HIGH HIGH HIGH EFFECT DIGITAL Block & Level Diagrams EMX62M—Owner’s Manual...
  • Page 26 YAMAHA CORPORATION V833080 R1 1 AP 24 Pro Audio & Digital Musical Instrument Division P.O. Box 3, Hamamatsu, 430-8651, Japan NP Printed in Taiwan...

Table of Contents