• Yamaha makes no representations or warranties with regard to the use of the software and documenta- tion and cannot be held responsible for the results of the use of this manual and the software.
mLAN Control Panel’s Manual What is mLAN Control Panel? “mLAN Control Panel” software enables you to set various parameters when you are using mLAN with a Macintosh computer. For example, it lets you specify the number of sequences and the sampling frequency of audio and MIDI data received or transmitted via mLAN, and specify where to receive or transmit such data.
mLAN Control Panel menu Apple menu About mLAN Control Panel... Displays the version information of mLAN Control Panel. File menu Close Closes mLAN Control Panel. Same as “Quit” in the File menu. Same as the [Set] button in the mLAN Control Panel window. Revert Same as the [Revert] button in the mLAN Control Panel window.
mLAN Control Panel window When you start mLAN Control Panel, the system displays the following window. All changes to the parameters in this window become valid when you click the [Set] button. FireWire Card ID This parameter displays the serial number of the FireWire (IEEE1394) interface card. If mul- tiple interface cards are installed on the computer, select the desired card here.
Send This column enables you to set parameters for mLAN data transmission. Checking the “Send” checkbox enables data transmission to the mLAN bus, and lets you make the necessary settings for transmission. If you do not perform mLAN transmission, remove the check from the checkbox. If you check the “Send”...
“Select Destinations” dialog box This dialog box enables you to specify the mLAN devices and mLAN plugs that receive mLAN data from the computer. Device pop-up menus These pop-up menus enable you to select mLAN devices to which data is transmit- ted.
Update Click this button to have the system check and update the condition of the con- nected mLAN devices. Use this button if the settings on the mLAN devices are changed after mLAN Control Panel is started. Revert Click to reset the dialog box to its original status when ﬁrst opened. Click to enable the dialog box settings and close the dialog box.
Isochronous Ch. This parameter determines and displays the Isochronous Channel number of the FireWire channel being used for mLAN data reception. The bar graph on the right displays the progress of reception. The bar graph scrolls when data is being received, and it stops when no data is received.
“Select Source” dialog box “Axx:” and “Mxx:” in the plug names mean “the xxth audio sequence” and “the xxth MIDI sequence” respectively. The sequences are received in the order shown in the Output Plugs list. Disconnect Click this button to cancel the device selection. Click [OK] under this condition to disconnect all virtual transmission (mLAN connections) from the mLAN devices to the computer.
Fit Sequences If the number of sequences does not match the actual number in the received data, a red warning message “Not Match” ﬂashes to the right of the number parameter. To match the number to that of the data being received, click this button. While the “Not Match”...
Click this button to enable the mLAN Control Panel settings. The settings do not take effect until you click the [Set] button. The settings in the dialog box that opens when you click the [Select Destina- tions...] or [Select Source...] button become valid when you click the [OK] button in the corresponding dialog box.
ASIO mLAN Driver’s Manual What is the ASIO mLAN driver? The “ASIO mLAN driver” software enables transmission and reception of audio data via mLAN, using an ASIO-supporting application program. Installing the driver Before you install the ASIO mLAN driver, ﬁrst install the mLAN driver and ASIO- supporting application program.
ASIO mLAN Control Panel When you start the ASIO mLAN Control Panel, the system displays the following dialog box (ASIO mLAN Control Panel). FireWire Card ID This parameter displays the serial number of the FireWire (IEEE1394) interface card. If mul- tiple interface cards are installed in the computer, select the desired card here.
Channel Assignment The pop-up menus in the “Send” and “Receive” columns enable you to specify which mLAN audio sequences are transmitted and received by the computer via which audio channels. The maximum number of audio channels is 32, but the maximum number of channels that can actually be used is equivalent to the number of audio sequences speci- ﬁed in the mLAN Control Panel.
mLAN OMS Driver’s Manual What is the mLAN OMS Driver? The “mLAN OMS Driver” software is used for MIDI data transfer with the mLAN bus via OMS. Using the mLAN OMS Driver enables MIDI data transmission and reception via mLAN, using sequencer software that supports OMS.
mLAN OMS Device Info dialog box Double-click the mLAN device icon, or select the mLAN device and select “MIDI Device Info...” from the “Studio” menu. The following Device Info dialog box appears. In this dialog box, you can use the pop-up menus in the “Send” and “Receive” columns to specify which mLAN MIDI sequences (that are transmitted and received by the computer) are assigned to which port.