Mitsubishi Electric MELSERVO-J3 Series Manual page 439

Part 7: Review on Replacement of Optional Peripheral Equipment
Servo amplifier
1) L1/L2/L3/
MR-J3-10_(1)
MR-J3-20_(1)
MR-J3-40_(1)
MR-J3-60_ 2 (AWG14)
MR-J3-70_
MR-J3-100_
MR-J3-200_
MR-J3-350_ 3.5 (AWG12)
MR-J3-500_
5.5 (AWG10): a
(Note 2)
MR-J3-700_
8 (AWG8): b
(Note 2)
MR-J3-11K_
14 (AWG6): c
(Note 2)
MR-J3-15K_
22 (AWG4): d
(Note 2)
MR-J3-22K_
38 (AWG1): p
(Note 2)
MR-J3-60_4
MR-J3-100_4 2 (AWG14)
MR-J3-200_4
MR-J3-350_4 2 (AWG14): g
MR-J3-500_4
(Note 2)
3.5 (AWG12): a
MR-J3-700_4
(Note 2)
MR-J3-11K_4
5.5 (AWG10): j
(Note 2)
MR-J3-15K_4
8 (AWG8): l
(Note 2)
MR-J3-22K_4
14 (AWG6): m
(Note 2)
Note 1. Alphabets in the table indicate crimping tools. For crimping terminals and applicable tools, refer to Section 4.2.1 of this
document.
2. To connect these models to a terminal block, make sure to use the screws that come with the terminal block.
3. For the servo motor with a cooling fan.
4. Wires are selected based on the highest rated current among combining servo motors.
Wire size selection example (HIV wire)
Power supply wire [mm
2) L11/L21 3) U/V/W/
1.25 (AWG16)
1.25 (AWG16)
1.25 (AWG16)
2 (AWG14)
3.5 (AWG12)
5.5 (AWG10): a
1.25 (AWG16): h
8 (AWG8): b
14 (AWG6): c
1.25 (AWG16): g 22 (AWG4): d
38 (AWG1): p
1.25 (AWG16)
1.25 (AWG16)
2 (AWG14)
2 (AWG14): g
3.5 (AWG12): a
1.25 (AWG16): h
5.5 (AWG10): a
8 (AWG8): l
1.25 (AWG16): g 14 (AWG6): c
14 (AWG6): m
7 - 16
2 ] (Note 1, 4)
4) P/C 5) B1/B2
2 (AWG14)
2 (AWG14): g
2 (AWG14): g
3.5 (AWG12): j 1.25 (AWG16)
5.5 (AWG10): k
2 (AWG14)
2 (AWG14): g
2 (AWG14): q
3.5 (AWG12): j
3.5 (AWG12): k
6) BU/BV/BW 7) OHS1/OHS2
1.25 (AWG16) 1.25 (AWG16)
(Note 3) (Note 3)
1.25 (AWG16) 1.25 (AWG16)
1.25 (AWG16) 1.25 (AWG16)
(Note 3) (Note 3)
1.25 (AWG16) 1.25 (AWG16)