Related Manuals for Xantech XDT77
Summary of Contents for Xantech XDT77
- Page 1 XDT77 AM/FM STEREO DUAL TUNER OWNER’S MANUAL Thank you for choosing XANTECH. Read this manual carefully to get the best performance from this unit.
-
Page 2: Important Safety Instructions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage"... -
Page 3: Table Of Contents
Contents Important Safety Instructions ......2 Contents ..........3 Before Use . -
Page 4: Connection
Connection CAUTION Turn off the power of all the equipment before making connections. Read instructions of each component you intend to use with this unit. < Be sure to insert each plug securely. To prevent hum and noise, do not bundle the connection cords with the power cord. -
Page 5: Am Indoor Loop Antenna
FM Antenna Connect an outdoor FM antenna to the FM 75Ω socket. Generally, a 3-element antenna will be sufficient; if you live in an area where the FM signals are particularly weak, it may be necessary to use one with 5 or more elements. If standard FM broadcast frequencies are available via your cable service, you may connect your 75 ohm FM antenna jack to your cable system. -
Page 6: Names Of Each Control
Names of Each Control E F G H Buttons for TUNER 1 E F G H Buttons for TUNER 2... - Page 7 REMOTE SENSOR When operating the remote control unit, point it towards the REMOTE SENSOR. STANDBY indicator This indicator lights when the unit is in the standby mode. When the unit is turned on, it goes off. POWER switch Press this switch to turn the unit on or off. The equipment draws nominal non-operating power from the AC outlet with its POWER switch in the OFF position.
-
Page 8: Radio Reception
TUNER 1 Press the POWER switch to turn the unit on. Select the AM or the FM band by pressing the corresponding button. Press the DIRECT button to select the manual tuning mode. Select the station you want to listen to. <... -
Page 9: Preset Tuning 1
Manual Memory Presetting You can store your favorite FM and AM stations into any of the 30 preset locations by: Select the AM or FM band by pressing the corresponding band button. Press the DIRECT button to select the “manual tuning” mode. Select the station you would like to store by scrolling through the station using the TUNING/PRESET buttons or directly tune the station by using the numeric buttons. -
Page 10: Troubleshooting
Preset Tuning 2 TUNER 1 How to select preset stations Select the AM or the FM band by pressing the corresponding button. Press the PRESET button. Select a preset channel using the numeric buttons. Or press the TUNING/PRESET button repeatedly until the desired preset station is found. -
Page 11: Specifications
Specifications FM Tuner Section (Without notes 98.1 MHz, 65 dBf) Tuning Range... 87.5 MHz – 107.9 MHz (200 kHz steps) Usable Sensitivity (IHF)......Mono: 15 dBf 50 dB Quieting Sensitivity . -
Page 12: Appendix A (Rs-232 Commands)
PURPOSE: This document describes the RS-232 commands that will operate the XANTECH XDT77 Dual Tuner through the 9-pin RS-232 connector on the rear panel. General Information: Data Rate: Parity: Word length: Handshake: Connections: DATA ENTRY PROTOCOL: The serial buss should follow a standard serial communications protocol using Line oriented ASCII data stream. - Page 13 Model number: Serial number: XDT77 Xantech Corporation 13100 Telfair Avenue, Second Floor Sylmar, CA 91342-3573 Sales: 800.843.5465 • Fax: 818.362.9506 Thank you for choosing XANTECH. Read this manual carefully to get the best performance from this unit.