1. Manuals
  2. Brands
  3. Worksaver Manuals
  4. Spreader
  5. CS-694, CS-1094, CSP-694, CSP-
  6. Owner's manual

Worksaver CS-694, CS-1094, CSP-694, CSP-1094 Owner's Manual

Broadcast seeder/spreader pto driven – 3-pt. mounted
Hide thumbs Also See for CS-694, CS-1094, CSP-694, CSP-1094:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's/operator's Manual
OWNER'S
MANUAL
MODEL NO.'S
CS-694
CS-1094
CSP-694
CSP-1094
CAUTION
For Operation
Read Rules And
Instructions Carefully
STATEMENT
OF POLICY
It is the policy of Worksaver,
Inc. to improve its products
where
it
is
possible
practical to do so. Worksaver,
Inc. reserves the right to make
changes or improvements in
design and construction at any
time
without
incurring
obligation
to
make
changes
on
manufactured units.
1. Read instruction manual and make sure all operators are knowledgeable on correct
operation of equipment and familiar with the Safety Rules of Operation.
2. Never allow riders on equipment.
3. When operating on rough or uneven terrain, use extreme caution and a safe operating speed.
4. When spreading seed or fertilizer, always use safety goggles.
5. Never operate equipment when anyone is within 50 feet of seeder/spreader.
BEFORE OPERATING EQUIPMENT : If you have any questions regarding the proper assembly or
operation, contact your dealer or representative.
Broadcast Seeder/Spreader
and
Packing
the
Assembly & Mounting
these
previously

Operating Instructions

ATTENTION! SAFETY RULES
P.O Box 100, Litchfield, IL. 62056-100
Phone: 217-324-5973 Fax: 217-324-3356
Web Site:
www.worksaver.com
PTO DRIVEN – 3-PT. MOUNTED
WORKSAVER, INC.
E-mail: sales@worksaver.com
Maintenance
Repair Parts

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CS-694, CS-1094, CSP-694, CSP-1094 and is the answer not in the manual?

Questions and answers

Related Manuals for Worksaver CS-694, CS-1094, CSP-694, CSP-1094

Summary of Contents for Worksaver CS-694, CS-1094, CSP-694, CSP-1094

  • Page 1: Operating Instructions

    CSP-1094 CAUTION For Operation Read Rules And Instructions Carefully STATEMENT OF POLICY It is the policy of Worksaver, Inc. to improve its products where possible practical to do so. Worksaver, Inc. reserves the right to make changes or improvements in...
  • Page 2 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached, to minimize the chance of accidents. Read the safety messages on the implement and shown in your manual.
  • Page 3 Measure the distance between the ends of the two shafts (Dimension “A”, Figure 1). Each half of the PTO should be equal to dimension “A” minus two (2) inches. If the driveline must be cut to a shorter length, clamp driveline in a well-padded vise to prevent damage to the shield (Figure 3).

  • Page 4: Spreading Instructions

    1. Right -hand or left-hand reference is determined by standing at the rear of the seeder/spreader and facing in the direction of travel of the tractor. 2. Check the register of the control lever indicator with the seed gate (material gate). With the seed gate closed, the control lever should be in its fully raised position.

  • Page 5: Maintenance

    Three spreading possibilities A simple adjustment of the lower level allows directioning of distribution towards the right side or towards the left side of the tractor operator. MAINTENANCE 1. The hopper should be washed after use, especially after use with corrosive material such as fertilizer, salt, or ice melting compounds.
  • Page 6 SPREADING CHART FOR FERTILIZERS FERTILIZER TYPE SPEED WIDTH (RPM) IN FEET Coarse Grain Fertilizers Medium Grain Fertilizers Fine Grain Fertilizers Ammonium Nitrate Urea (Carbamide) Spread widths of fertilizer will vary according to type. Always check actual spread width and application rate. Spread Chart settings are approximate –...
  • Page 7 SPREADING CHART FOR SEED S P R E A D T R A C T O R M A T E R I A L I N F E E T A l f a l f a & C l o v e r B a r l e y B l u e g r a s s &...
  • Page 8 EXPLODED PARTS DRAWING FOR CS SERIES SPREADERS Page 8...
  • Page 9 REPAIR PARTS FOR CS SERIES SEEDER/SPREADERS Ref. No Part No. 420701 Frame, XA 420702 Bolt, Hex Head, M8 x 20, Zinc 420703 Washer, Flat, 8mm, Zinc 420704 Washer, Flat, 10mm, Zinc 420705 Nut, Self-Locking, M10, Zinc 420706 Washer, Bakelite 420707 Lever, Adjustment 420708 Handle, Rubber, 8 x 20...
  • Page 10 PTO COMPONENTS Ref. No Part No. 420748 PTO Assembly, Complete 420764 PTO Half, Tractor End 420765 Plastic Shield Assembly, Outer 420766 PTO Half, Implement End 420767 Plastic Shield Assembly, Inner 170804 Yoke, 1-3/8-6B Spline 3814091 PTO Cross Repair Kit 170806 Push Pin Repair Kit, Yoke 101081 Decal, Driveline Entanglement...

  • Page 11: Gearbox Components

    OPTIONAL AGITATOR COMPONENTS Ref. Part Description 420725 Agitator, Complete 420759 Wheel, Agitator 420760 Washer, Flat, M12 420761 Nut, Self-Locking, M12, Zinc 420710 Bolt, Hex Head, M10 x 65, Zinc 420717 Nut, Hex, M10, Zinc GEARBOX COMPONENTS Ref. Part Description 420747 Gearbox, 3-Hole (Complete) 420749 Gearbox Half, Right Hand 420750 Shaft, Output Assembly 420751 Oil Seal, 25 x 37 x 5...

  • Page 12: Safety Precautions

    (5) parts failing through use of implement for purposes other than those for which it was designed. The obligations assumed by Worksaver and the limitations expressed herein are in lieu of all other warranties expressed or implied.

Table of Contents