Advertisement
Quick Links
TravelNet Internet Only Cellular Router Installation Guide
Parts List:
• TravelNet Cellular Router (TN-2033, TN-2055)
• 110 volt adapter with green connector
• Edimax BR-6204WG WiFi Preconfigured Router
• 110 volt adapter with plug connector
• 3 foot Ethernet Cable
• (2)External Antenna (white)
• (2)External Antenna mount with 14' cable
• (2)Stainless Antenna Mounts
• Cable Entry Cover
• Aluminum Ground Plane (7 x 7 )
• Customer Package (clear envelope)
o 7 foot Red Ethernet Cable
o (2)Black SMA Antenna
o TravelNet Quick Start,
o TravelNet User CD
• User Manual
• Troubleshooting Guide
Other items not included:
• Sealant (Consult your vehicle manufacturer for the best sealant for your roof
material.)
Ver. 1.5
4/1/2009
ATTENTION INSTALLER
- 1 -
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Winegard TRAVELNET TN-2033
Summary of Contents for Winegard TRAVELNET TN-2033
- Page 1 TravelNet Internet Only Cellular Router Installation Guide ATTENTION INSTALLER Parts List: • TravelNet Cellular Router (TN-2033, TN-2055) • 110 volt adapter with green connector • Edimax BR-6204WG WiFi Preconfigured Router • 110 volt adapter with plug connector • 3 foot Ethernet Cable •...
- Page 2 TravelNet’s Cellular Router System is Preconfigured And Ready to Install with these Easy Steps Installation Instructions: 1. Install the TravelNet Router and Edimax Router equipment in a convenient place such as upper cabinet (Velcro works well on the base of the each unit). Mount the unit so that the diagnostic lights can be viewed without moving the TravelNet Router and the Edimax Wireless Router.
- Page 3 Note that the antenna mounts are anchored to the 7” x 7” aluminum ground plane and that everything is well sealed. 3. Insert the small end of the cable through the ¾” diameter hole in the stainless antenna mount and feed the cable through. Next screw the brass antenna mount nut to the antenna mount as shown above, with the O-ring down, and attach the Antennas.
- Page 4 4. Route the 2 antenna cables to the cable entry hole in the coach roof. Securely attach the cable entry cover over the cable entry point on the coach roof using screws and caulk (Figure 6) Antenna cables should be directed to the TravelNet Router. 5.
- Page 5 6. Carefully attach the antenna cables to the SMA Antenna Mounts on the TravelNet router. Caution should be taken to not over tighten the SMA cable connectors. 7. Connect power supplies for both devices to AC source or 12VDC source. When a 12 VDC source, order the appropriate pigtail accessories and please save the 12 volt power supply for the coach owner.
- Page 6 8. Check table below for LED status. Light Status LINK No Connection (IP address) Green-- 1XRTT Connection Red— EV-DO Connection 9. If you are activating the TravelNet Cellular Router, precede to the activation instructions for the correct TravelNet model. See below: Sprint or Verizon 10.
- Page 7 Activation Instructions for model TN-2055 and TN-2033: Sprint TN-2033 users skip to page 9 Verizon TN-2055 Activation: 1. Connect an Ethernet Cable directly to the TravelNet Cellular Router and the Laptop. 2. Enable the Local Area Network, when connected, go to the next step. 3.
- Page 8 8. Click on the Over The Air Activation 9. If Network Stability is OK For Activation minutes.) If Not OK for Activation for 15 additional minutes, contact Support. 10. Click the Activate button. 11. Wait 3 minutes, then check status. If still in progress, wait an additional 3 minutes.
- Page 9 19. Click on the Status-Wireless This may take several minutes depending on the carrier network. 20. Click on the Home button. 21. Click on the Restart button and confirm by clicking the wait 30 seconds. 22. Do a restart of all network devices in order, first the TravelNet Router, 2 Edimax Router, and finally laptop.
- Page 10 5. Enter the user name ‘ctek’ and password ‘ctek’ 6. Click the Log In button. 7. Click on the Activation 8. Click on the Over the Air Activation 9. If Network Stability is Ok for Activation minutes. If still Not Ok, call support. 10.
- Page 11 15. At the bottom of the page, click the 16. Ok, then click the Home 17. Click on the Restart button and confirm by clicking the wait 30 seconds. 18. Click on the Home button. 19. Click the Status-Wireless 20. Click on the Home button.
- Page 12 WEP Key Setup 1. Log into the Edimax WiFi Router at 192.168.2.1 2. Enter the Username ‘admin’ and Password ‘1234’ 3. Go to WIRELESS SETTINGS > SECURITY 4. Encryption type: select WEP 5. Key Length: 64-bit 6. Key Format: Hex (10 Characters) 7.
-
Page 13: Wep Key Setup
WEP Key Setup Parameters Default Description Key Length 64-bit You can select the WEP key length for encryption, 64-bit or 128-bit. Larger WEP key length requires 26 hexadecimal characters Key Format Use hexadecimal digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key. - Page 14 To connect your XP computer to your wireless network Configuring the Windows XP Wireless Clients (With WEP) Configuration of the Windows XP wireless clients for WEP key authentication depends on whether you are using Windows XP with SP2 or Windows XP with SP1 and whether the wireless network adapter driver supports Wireless Auto Configuration.
- Page 15 To connect your Windows Vista computer to your wireless network View and connect to available wireless networks Applies to all editions of Windows Vista. If you have a mobile PC, you can see a list of available wireless networks, and then connect to one of those networks, no matter where you are.
- Page 16 QUESTIONS? CALL OUR SUPPORT LINE: 877-475-7771 or visit our website FAQ at http://www.winegard.com TravelNet Winegard Company Support: (877) 475-7771 FAX: 847-991-3328 Ver. 1.5 4/1/2009 - 16 -...
Need help?
Do you have a question about the TRAVELNET TN-2033 and is the answer not in the manual?
Questions and answers