Siemens SINUMERIK 840D Diagnostics Manual page 382

1 Alarms
1-382
• 31 Actual position tolerance $MA_SAFE_POS_TOL. $MA_SAFE_SLIP_VELO_TOL for
active actual value synchronization (slippage)
• 32 Ref. position tolerance $MA_SAFE_REFP_POS_TOL.
• 33 Delay SG[x] -> SG[y] $MA_SAFE_VELO_SWITCH_DELAY.
• 34 Delay cross-comparison $MA_SAFE_MODE_SWITCH_TIME.
• 35 Delay pulse disable Stop B $MA_SAFE_PULSE_DISABLE_DELAY.
• 36 Delay pulse disable test stop $MA_SAFE_PULSE_DIS_CHECK_TIME
• 37 Delay Stop C -> SBH $MA_SAFE_STOP_SWITCH_TIME_C.
• 38 Delay Stop D -> SBH $MA_SAFE_STOP_SWITCH_TIME_D.
• 39 Delay Stop E -> SBH $MA_SAFE_STOP_SWITCH_TIME_E.
• 40 Stop reaction on SG exceeded $MA_SAFE_VELO_STOP_MODE.
• 41 Stop reaction on SE exceeded $MA_SAFE_POS_STOP_MODE.
• 42 Standstill speed $MA_SAFE_STANDSTILL_VELO_TOL.
• 43 Memory test, stop reaction.
• 44 Actual position + SG[0] $MA_SAFE_VELO_LIMIT[0].
• 45 Actual position - SG[0] $MA_SAFE_VELO_LIMIT[0].
• 46 Actual position + SG[1] $MA_SAFE_VELO_LIMIT[1].
• 47 Actual position - SG[1] $MA_SAFE_VELO_LIMIT[1].
• 48 Actual position + SG[2] $MA_SAFE_VELO_LIMIT[2].
• 49 Actual position - SG[2] $MA_SAFE_VELO_LIMIT[2].
• 50 Actual position + SG[3] $MA_SAFE_VELO_LIMIT[3].
• 51 Actual position - SG[3] $MA_SAFE_VELO_LIMIT[3].
• 52 Standstill position + tolerance $MA_SAFE_STANDSTILL_TOL.
• 53 Standstill position - tolerance $MA_SAFE_STANDSTILL_TOL.
• 54 Actual position + n_x + tolerance $MA_SAFE_VELO_X + $MA_SAFE_POS_TOL.
• 55 Actual position + n_x $MA_SAFE_VELO_X.
• 56 Actual position - n_x $MA_SAFE_VELO_X.
• 57 Actual position - n_x - tolerance $MA_SAFE_VELO_X - $MA_SAFE_POS_TOL
• 58 Active external standstill request.
• 59 SG override factor 1 $MA_SAFE_VELO_OVR_FACTOR[0].
• 60 SG override factor 2 $MA_SAFE_VELO_OVR_FACTOR[1].
• 61 SG override factor 3 $MA_SAFE_VELO_OVR_FACTOR[2].
• 62 SG override factor 4 $MA_SAFE_VELO_OVR_FACTOR[3].
• 63 SG override factor 5 $MA_SAFE_VELO_OVR_FACTOR[4].
• 64 SG override factor 6 $MA_SAFE_VELO_OVR_FACTOR[5].
• 65 SG override factor 7 $MA_SAFE_VELO_OVR_FACTOR[6].
• 66 SG override factor 8 $MA_SAFE_VELO_OVR_FACTOR[7].
• 67 SG override factor 9 $MA_SAFE_VELO_OVR_FACTOR[8].
• 68 SG override factor 10 $MA_SAFE_VELO_OVR_FACTOR[9].
• 69 SG override factor 11 $MA_SAFE_VELO_OVR_FACTOR[10].
• 70 SG override factor 12 $MA_SAFE_VELO_OVR_FACTOR[11].
• 71 SG override factor 13 $MA_SAFE_VELO_OVR_FACTOR[12].
• 72 SG override factor 14 $MA_SAFE_VELO_OVR_FACTOR[13].
• 73 SG override factor 15 $MA_SAFE_VELO_OVR_FACTOR[14].
• 74 SG override factor 16 $MA_SAFE_VELO_OVR_FACTOR[15].
• 75 Velocity limit n_x $MA_SAFE_VELO_X.
• 76 Stop reaction SG1 $MA_SAFE_VELO_STOP_REACTION[0].
• 77 Stop reaction SG2 $MA_SAFE_VELO_STOP_REACTION[1].
• 78 Stop reaction SG3 $MA_SAFE_VELO_STOP_REACTION[2].
• 79 Stop reaction SG4 $MA_SAFE_VELO_STOP_REACTION[3].
 Siemens AG, 2004. All rights reserved
SINUMERIK 840D/840Di/810D Diagnostics Guide (DA), 10.04 Edition
10.04