Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
REAR TINE
TILLER
MODEL
RB650
21A-458B190
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.
WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
FORM NO.770-10193
(12/98)
Advertisement
Table of Contents
Related Manuals for White RB650
Summary of Contents for White RB650
- Page 1 Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722. WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A.
-
Page 2: Section 1: Finding Your Model Number
• Every tiller has a model plate. You can locate it by standing in the operating position behind the unit and looking down at the center of the rear tine cover. • The model plate will look like Figure 1. XXX-X-XXX-X-XXX XXXXXXXXXXX WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136... -
Page 3: Section 3: Important Safe Operation Practices
SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TILLER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. - Page 4 • Only use accessories approved for this machine by the manufacturer. Read, understand, and follow all instructions provided with the approved accessory. • If situations occur which are not covered by this manual, use care and good judgment. Contact your dealer for assistance.
-
Page 5: Section 4: Loose Parts
SECTION 4: LOOSE PARTS Handle Assembly Depth Stake Control Assembly NOTE: Cable tie not shown. -
Page 6: Section 5: Assembly Instructions
SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE: Left and right is determined from the operator’s position, standing behind the tiller. TOOLS REQUIRED FOR ASSEMBLY Adjustable Wrenches Pair of Pliers... - Page 7 Slot in Cable Bracket Washer Figure 5 ATTACHING THE CLUTCH CABLE Attach the clutch cable to the handle as follows (be careful not to kink the cable). 1. Route the clutch cable to the left side of the tiller, and underneath the handle. Remove one hex nut and lock washer from the end of the casing on the clutch cable.
-
Page 8: Section 6: Controls
Position the tiller so the front counterweight is against a solid object, such as a wall. With the gear selection lever in NEUTRAL, start the engine. Refer to the separate engine manual. Standing on the right side of the tiller, examine the belt (inside the belt cover). -
Page 9: Section 7: Operation
DEPTH STAKE The depth bar controls the tilling depth. Refer to SECTION 8: HOW TO USE YOUR TILLER on page SECTION 7: OPERATION NOTE: Engine is shipped without oil. WARNING: Before operating the tiller, be certain to read SECTION 8: HOW TO USE YOUR TILLER on page 9. -
Page 10: Section 9: Adjustments
Use This Position First Time Clevis Figure 9 4. To transport tiller, lower the depth stake (use top adjustment hole). 5. To adjust the depth stake, remove the clevis pin and hairpin clip. See Figure 9. Move the depth stake to the desired setting. 6. -
Page 11: Carburetor Adjustment
To adjust the tension on the belt, refer to clutch adjustment information in “Checking the Clutch Adjustment” section of the Assembly Instructions. After belt tension has been adjusted, if the belt is excessively stretched, you may need to adjust the idler pulley rod. -
Page 12: Belt Replacement
BELT REPLACEMENT CAUTION: Do not use an off-the-shelf belt. Your tiller has been engineered with a belt made of special material (Kevlar Tensile) for longer life and better performance. It should not be replaced with an off-the-shelf belt. If belt replacement is required, order belt or belts by part number from your nearest authorized dealer. -
Page 13: Section 12: Off-Season Storage
SECTION 12: OFF-SEASON STORAGE If the tiller will not be used for a period longer than 30 days, the following steps should be taken to prepare the tiller for storage. 1. Clean the exterior of engine and the entire tiller thoroughly. - Page 14 Model 458...
- Page 15 Model 458 REF. PART NO. 611-0020 Wheel Shaft Ass’y: 33T 611-0021 Tine Shaft Ass’y: 18T 611-0128 Jack Shaft Ass’y 611-0129 Input Shaft Ass’y 617-0058 Rev. Idler Gear Ass’y: 30T 617-0059 Ftine Idler Gear Ass’y: 30T 617-0060 Tine Input Sprocket Ass’y: 9T 617-0061 Wheel Input Sprocket Ass’y: 10T 617-0062...
- Page 16 Model 458...
- Page 17 Description 777S30038 Model Plate 777I20282 Shift Plate Facing Operator 777D02264 Engine Spinner 777D02263 White, Side of Belt Guard 777I20358 Place Hand Here on Handle 777I20451 Gear Selection on Handle PART NO. DESCRIPTION Hex Screw 5/16-18 x .75" Lg. Spacer .435 O.D. x .322 I.D.
- Page 18 Model 458 3 40...
- Page 19 Model 458 REF. PART NO. 686-0111 Belt Cover Brkt. Ass’y 710-0237 Hex Bolt 5/16-24 x .62" Lg. 710-0412 Hex Bolt 1/4-28 x .75" Lg. 710-0502A Hex Wash.TT-Sems Screw 3/8-16 x 1.250" Lg. 710-0591 Hex Bolt 3/8-24 x 1.00 710-0599 Hex Wash. Hd. S-Tap Scr. 710-0723 Hex Cap Screw 3/8-16 x 1.25 712-0266...
- Page 20 5. The provisions as set forth in this warranty provide the sole and exclusive remedy of White Outdoor Products Company’s obligations arising from the sales of its products. White Outdoor Products Company will not be liable for incidental or consequential loss or damage.