1. Manuals
  2. Brands
  3. White Manuals
  4. Tiller
  5. 414
  6. Operator's manual

White 414 Operator's Manual

Rear tine tiller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
M
PERATOR'S
ANUAL
REAR TINE
TILLER
Model
414
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.
WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
FORM NO. 770-10183
(10/98)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 414 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for White 414

Summary of Contents for White 414

  • Page 1 Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722. WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A.

  • Page 2: Section 1: Finding Your Model Number

    • Every tiller has a model plate. You can locate it by standing in the operating position behind the unit and looking down at the frame on the right side. XXX-X-XXX-X-XXX XXXXXXXXXXX WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136...

  • Page 3: Section 3: Important Safe Operation Practices

    SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TILLER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
  • Page 4 • Only use accessories approved for this machine by the manufacturer. Read, understand, and follow all instructions provided with the approved accessory. • If situations occur which are not covered by this manual, use care and good judgment. Contact your dealer for assistance.

  • Page 5: Section 4: Unpacking

    SECTION 4: UNPACKING TO REMOVE UNIT FROM CARTON 1. Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. 2. Remove loose parts included with unit (i.e., owner’s manual, etc.). 3.
  • Page 6 Flange Nut Retainer Bracket Shoulder Bolt Lock Nut Handle Adjustment Lock Flange Nut Pivot Bracket Figure 4 3. Lift up the handle assembly and align the bottom holes in the handle assembly with the holes in the pivot bracket. Insert hex bolt (with Hex nut retainer attached through the round hole).

  • Page 7: Tire Pressure

    Handle Adjustment Lock Flange Lock Nut Figure 9 2. Slip the wire up through the slot on the cable bracket underneath the handle. Push the end of the casing up through the cable bracket. Rethread the hex nut on the end of the cable. Do not tighten at this time.

  • Page 8: Section 6: Controls

    SECTION 6: CONTROLS Gear Selection Handle Handle Height Adjustment Lock Figure 11 GEAR SELECTION HANDLE The gear selection handle is located on the front of the handle assembly. It is used to select NEUTRAL, REVERSE, or one of the FORWARD modes. This tiller is designed for the gear selection handle to be moved while the engine is running.

  • Page 9: To Stop Engine

    5. Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle. 6. Repeat steps 4 and 5 until engine starts. 7. As engine warms up and begins to operate evenly, move choke lever gradually to RUN position.

  • Page 10: Section 8: Adjustments

    4. Squeeze the clutch handle against the handle to engage the wheels and tines. NOTE: Make certain the gear selection indicator is correctly positioned before engaging the clutch handle. If it is between gears, the engine will stall. To transport tiller, do not engage the tines. Select the wheel drive only.

  • Page 11: Belt Replacement

    Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all dirt and combustible debris from muffler area.

  • Page 12: Section 12: Trouble Shooting Guide

    SECTION 12: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Engine fails to Fuel tank empty, or stale fuel. start Throttle control lever not in correct starting position (if so equipped). Blocked fuel line. Dirty aircleaner. Choke not in ON position. Spark plug wire disconnected. Faulty spark plug.
  • Page 13 Notes...
  • Page 14 Model 414...
  • Page 15 Model 414 REF. PART DESCRIPTION 735-0246 Vinyl End Plug 647-0014 Clutch Control Ass’y. 710-1017 Torx Mach. AB-Tap Scr. 1/4 x .62" 786-0131 Handle Cover 786-0098 Retaining Brkt.—R.H. 786-0118 Retaining Brkt.—L.H. 720-0278 Grip (2 Req’d.) 720-0210A Knob 712-3008 Hex Jam Nut 3/8-16 Thd.
  • Page 16 Model 414 REF. PART NO. 710-3008 Hex Bolt 5/16-18 x .75" Lg. 712-3004A Hex Top L-Nut 5/16-18 Thd. 786-0107 Cable Mtg. Bracket 710-1017 Torx Mach. AB-Tap Scr. 1/4 x .6" Lg 738-0899 Belt Cover Bolt 786-0117 Shift Cover Bracket 786-0100...
  • Page 17 Models 414 REF. PART NO. 721-0295 Chain Case Gasket 786-0086 Reinforcement Plate 716-0865 Snap Ring 750-0938 Spacer .735" I.D. x .886" O.D. 611-0058 Wheel Shaft 717-1458 Spur Gear 46T 736-0351 Fl-Wash. .76" I.D. x 1.5" O.D. 721-0379 Shaft Seal 736-0518 Thr.Wash..445 I.D.x1.92 O.D.x .060...
  • Page 20 5. The provisions as set forth in this warranty provide the sole and exclusive remedy of White Outdoor Products Company’s obligations arising from the sales of its products. White Outdoor Products Company will not be liable for incidental or consequential loss or damage.

Table of Contents