Advertisement
Table of Contents
- 1 Product View
- 2 Parts and Accessories
- 3 Battery Installation
- 4 Threading the Machine
- 5 Threading Main Unit Using Side Bobbin
- 6 Winding the Bobbin
- 7 Bottom Bobbin Placement
- 8 Controlling the Sewing Speed
- 9 To Use with Foot Pedal
- 10 Adjusting Thread Tension
- 11 Stitch Length Adjustment
- 12 Reverse Sewing
- 13 Changing the Needle
- 14 Troubleshooting
- Download this manual
Advertisement
Table of Contents
Related Manuals for White SEW E-Z W338
Summary of Contents for White SEW E-Z W338
- Page 1 Sew E-Z Model W338 Mini Sewing Machine Instruction Manual Please read the instruction manual carefully before operating the machine. Call Toll Free 800-331-3164 www.whitesewing.com...
-
Page 2: Product View
Take Up Lever (D) Tension Screw (Q) Needle Clamp Screw (O) Needle Clamp (P) Needle (R) Presser Foot (F) Bobbin compartment (I) Bobbin Holder (J) Bobbin Winder Handler (W) Battery Compartment (B) on underside of machine Introduction Thread Spindle (C) Thread Spool (E) Bobbin Holder (V) Bobbin (S) -
Page 3: Parts And Accessories
Parts & Accessories AC/DC Adapter (DC 6V) Foot Pedal Jack (M) Accessories Needle Threader, Tape measure, Seam ripper, Thimble, Thread, Buttons, Needles, Pins, Scissors, Bobbins, Snaps... -
Page 4: Battery Installation
Battery Installation 1. Caution: Make certain the POWER SWITCH is in the off position before inserting the batteries. 2. Insert (4)AA batteries in the battery slot compartment in the bottom of the machine. Be certain the batteries are in the correct polarities as marked on the machine. Then replace the battery compartment cover. -
Page 5: Threading The Machine
Threading the machine Threading the machine 1. Raise thread spindle (C) by grasping the exposed top and pulling upward until thread spindle (C) is fully extended. 2. Place thread spool (E) on the thread spindle (C) as shown. 3. Pull thread from the thread spool (E) on the thread spin- dle (C) and put it through the thread holder (1) in the direc-... -
Page 6: Winding The Bobbin
Bobbin Winding and Insertion Winding the bobbin You can wind your own bobbins with thread from spools you purchase separately to have a virtually unlimited thread color selection. Match your fabrics or contrast with the thread shades of your choice. 1. - Page 7 Operating the Sew E-Z Rotate the handwheel to bring the needle to the highest position. Lower the presser foot. Lift the presser foot and place fabric under the presser foot. Press the power switch to begin sewing. Don’t pull the fabric.
-
Page 8: Controlling The Sewing Speed
Operating the Sew E-Z Operating the machine without the foot pedal 1. Lift the needle (R) above the presser foot (F) by turning the had wheel (K) slightly in clockwise direction (away from you.) 2. Raise the presser foot (F) by lifting up on the rear at the machine above the Presser foot bar. 3. -
Page 9: Adjusting Thread Tension
Operating the Sew E-Z Adjusting thread tension Tension for maximum performance has been set and adjusted at the factory. However, if you should find that stitches are too loose, or too tight, you can adjust the stitch. 1. Loosen stitch by turning the tension screw (Q) counter-clockwise. -
Page 10: Changing The Needle
Changing the Needle 1. Turn the handwheel (K) clockwise to raise the needle (R) to its highest position. 2. Loosen the needle clamp screw (O) by turning it counter-clockwise (toward you). You may need to use a short slotted screwdriver or small pliers. -
Page 11: Troubleshooting
Set the POWER switch to OFF and don’t touch the switch when inserting batteries or plugging in or replacing the needle. Keep the unit away from children. If operated by a child, an adult shall watch the operation. Set the switch to OFF after usage and remove the batteries or pull off the plug. Don’t mix old batteries with new ones. - Page 12 ©2006 VSM Sewing Inc. White is a registered trademark. All rights reserved.