Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Teknik Manuals
  4. Indoor Furnishing
  5. Scribed Oak Storage Desk 5418294
  6. Instruction booklet

Teknik Scribed Oak Storage Desk 5418294 Instruction Booklet

Hide thumbs

Advertisement

Quick Links

Download this manual
www.teknikoffice.co.uk
Scribed Oak Storage Desk
5418294
Teknik
For all your
newfangled gadgetry.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-32
Français pg 33-36
Español pg 37-40

Advertisement

loading
Need help?

Need help?

Do you have a question about the Scribed Oak Storage Desk 5418294 and is the answer not in the manual?

Questions and answers

Related Manuals for Teknik Scribed Oak Storage Desk 5418294

Summary of Contents for Teknik Scribed Oak Storage Desk 5418294

  • Page 1 Teknik www.teknikoffice.co.uk For all your newfangled gadgetry. Scribed Oak Storage Desk 5418294 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-32 Français pg 33-36 Español pg 37-40...
  • Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-32 Hammer Not actual size Electric drill with 1/4" bit (ONLY in indicated step) Safety Now you know Part Identifi...
  • Page 3 Part Identifi cation D216 D464 D713 D216 D464 D463 D102 D713 D463 D102 Page 3...
  • Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) EXTENSION EXTENSION CABINET CABINET DRAWER DRAWER 40CA 40CB 40CC 40CD RAIL - 2 SLIDE - 2 RIGHT - 1 LEFT - 1 RIGHT - 1 LEFT - 1...
  • Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. STOP Push eighteen HIDDEN CAMS (1F) into the ENDS (A, B, å and C), UPRIGHTS (D and E), BOTTOM (H), and UPPER If you SHELF (J).
  • Page 6 Step 2 Separate the EXTENSION SLIDES (Y) from the å EXTENSION RAILS (X) as shown in the enlarged diagram Remember: below. Be prepared, the parts are greasy. Righty tighty. Lefty loosey. Fasten the EXTENSION RAILS (X) to the RIGHT END (A) å...
  • Page 7 Step 3 Fasten the CABINET RIGHT (40CA) to the RIGHT END (A) å and CABINET LEFT (40CB) to the UPRIGHT (D). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Roller end Notched edge Roller end Finished edge GOLD 5/16"...
  • Page 8 Step 4 Fasten the SIDE SKIRTS (O) to the RIGHT END (A), LEFT å ENDS (B and C), and LEFT UPRIGHT (E). Use eight BROWN 1" FLAT HEAD SCREWS (12S). BROWN 1" FLAT HEAD SCREW (8 used in this step) Unfi...
  • Page 9 Step 5 Fasten the INNER LEFT END (C) to the MODESTY PANEL (I). å Caution Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Do not stand the unit upright without the BACK fastened. The unit may collapse. BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) S u r f a c...
  • Page 10 Step 6 IMPORTANT: If you purchased the 418295 Hutch, you will å need to fi nish drilling through the three partially drilled holes in the TOP (G) using your drill and 1/4" drill bit. BROWN 1" FLAT HEAD SCREW Fasten the TOP MOLDING (R) to the TOP (G). Use fi ve å...
  • Page 11 Step 7 Fasten the OUTER LEFT END (B) to the TOP (G). Tighten å two HIDDEN CAMS. D E N H I D i t h f a c S u r Caution Start Tighten Risk of damage or Arrow injury.
  • Page 12 Step 8 Fasten the INNER LEFT END (C) assembly to the TOP (G). å Tighten two HIDDEN CAMS. Maximum Arrow 210 degrees Minimum 190 degrees D E N H I D i t h f a c S u r For support, place packing foam and magazines here.
  • Page 13 Step 9 Fasten the LEFT UPRIGHT (E) to the TOP (G). Tighten two å HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the LEFT UPRIGHT (E) to the MODESTY PANEL (I). å Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Minimum 190 degrees Notched edge i t h o...
  • Page 14 Step 10 NOTE: Separate the LEFT END MOLDINGS (T and W). The å LEFT FRONT END MOLDING (T) is shorter than the LEFT REAR END MOLDING (W). Do not confuse these MOLDINGS. Slide the LEFT FRONT END MOLDING (T) onto the notched å...
  • Page 15 Step 11 Slide the PLINTH (S) onto the notched edges of the LEFT å ENDS (B and C). Push a DOOR STOP (4I) into the hole in the LEFT å UPRIGHT (E). *U.S. Patent No. 5,499,886 å Finished edge Slide the PLINTH (S) onto the notched edges.
  • Page 16 Step 12 Insert four METAL PINS (1R) into the SMALL UPRIGHT (F). å Insert the METAL PINS (1R) in one end of the SMALL UPRIGHT (F) into the holes in the TOP (G). å Fasten the UPPER SHELF (J) to the LEFT UPRIGHT (E). Tighten two HIDDEN CAMS. å...
  • Page 17 Step 13 Slide the RIGHT UPRIGHT END MOLDING (U) onto the å notched edge of the LEFT UPRIGHT (E). *U.S. Patent No. 5,499,886 å Slide the RIGHT UPRIGHT END MOLDING (U) onto the notched edge. Page 17...
  • Page 18 Step 14 Fasten the UPRIGHT (D) to the UPPER SHELF (J). Tighten å two HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Finished edge w i t h f a c e C A M S u r D E N H I D...
  • Page 19 Step 15 Slide the SHELF MOLDING (V) onto the notched edge of å the UPPER SHELF (J). *U.S. Patent No. 5,499,886 å Notched edge Slide the SHELF MOLDING (V) onto the notched edge. Page 19...
  • Page 20 Step 16 Fasten the BOTTOM (H) to the LEFT UPRIGHT (E). å Tighten two HIDDEN CAMS. Fasten the BOTTOM (H) to the UPRIGHT (D). Use two å BLACK 1-7/8" FLAT HEAD SCREWS (2S). This hole must be here. S u r f a c H I D D E N...
  • Page 21 Step 17 Fasten the RIGHT END (A) to the TOP (G), BOTTOM (H), å and UPPER SHELF (J). Tighten six HIDDEN CAMS. Maximum Arrow 210 degrees Slide the RIGHT UPRIGHT END MOLDING (U) onto the å notched edge of the RIGHT END (A). Minimum *U.S.
  • Page 22 Step 18 Fasten three METAL BRACKETS (4G) to the RIGHT END (A), å LEFT UPRIGHT (E), and BOTTOM (H). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edges å of the RIGHT END, LEFT UPRIGHT, and BOTTOM. Fasten the BASE (N) to the RIGHT END (A), LEFT å...
  • Page 23 Step 19 Carefully turn your unit over onto its front edges. Unfold the BACK (K) and lay it over your unit. å Make equal margins along all four edges of the BACK (K). Push on opposite corners of your unit if needed to make it "square". å...
  • Page 24 Step 20 Fasten two HINGES (40H) to the DOOR (L). Use four å BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2” FLAT HEAD SCREW (4 used in this step) Page 24...
  • Page 25 Step 21 Carefully stand your unit upright. å Pro Tip: Lift with your Before fastening the DOOR to your unit, be sure the å legs. And, you know, mounting screw is against the stops as shown in the right your arms. diagram.
  • Page 26 Step 22 Refer to the enlarged diagram to identify the parts on å the HINGES. The DOORS may need some adjustments. Follow the text å below to make needed adjustments. DOOR ADJUSTMENTS: å To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out.
  • Page 27 Step 23 Fasten a LARGE DRAWER BOX FRONT (D463) to the LARGE DRAWER SIDES (D102). Use four BLACK 1-9/16" FLAT å HEAD SCREWS (30S). Slide a DRAWER BOTTOM (D713) into the grooves in the LARGE DRAWER SIDES (D102) and LARGE DRAWER BOX å...
  • Page 28 Step 24 Fasten the LARGE DRAWER FRONT (Q) to a LARGE å DRAWER BOX FRONT (D463). Use four BLACK 7/8" LARGE HEAD SCREWS (17S). Repeat this step for the other drawer using DRAWER å FRONT (P). This drawer will use only two BLACK 7/8" LARGE HEAD SCREWS (17S).
  • Page 29 Step 25 Fasten the EXTENSION SLIDES (Y) to the LARGE å DRAWER SIDES (D102). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Open end D102 D102 Open end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 29...
  • Page 30 Step 26 Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) å to the DRAWER SIDES (D216). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4. Roller end D216 Roller end D216 GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 30...
  • Page 31 Step 27 Fasten a PULL (70K) to the DRAWER FRONT (P). Use two SILVER 1-1/2" MACHINE SCREWS (95S) through the DRAWER å BOX FRONT, through the DRAWER FRONT, and into the PULL. Fasten a PULL (70K) to the LARGE DRAWER FRONT (Q). Use two GOLD 1" MACHINE SCREWS (50S). å...
  • Page 32 Step 28 Push the RUBBER SLEEVES (2R) over the remaining METAL PINS (1R). Insert the METAL PINS into the hole locations of å your choice in the UPRIGHTS (D and E). Set the ADJUSTABLE SHELF (M) onto the METAL PINS. To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on å...
  • Page 33 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. •...