Table of Contents
Advertisement
Quick Links
30" (76.2 CM) FREESTANDING GAS RANGES
RANGE SAFETY............................................................................................................ 2
INSTALLATION REQUIREMENTS............................................................................... 3
Tools and Parts........................................................................................................... 3
Location Requirements............................................................................................... 4
Electrical Requirements.............................................................................................. 5
Gas Supply Requirements.......................................................................................... 6
INSTALLATION INSTRUCTIONS................................................................................. 7
Unpack Range ............................................................................................................ 7
Install Anti-Tip Bracket ............................................................................................... 7
Make Gas Connection................................................................................................ 9
Verify Anti-Tip Bracket Location............................................................................... 10
Level Range .............................................................................................................. 10
Electronic Ignition System ........................................................................................ 10
Complete Installation ................................................................................................ 11
GAS CONVERSIONS .................................................................................................. 12
LP Gas Conversion................................................................................................... 12
Complete Conversion............................................................................................... 14
Natural Gas Conversion............................................................................................ 14
Complete Conversion............................................................................................... 16
IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
W10032070B
INSTALLATION INSTRUCTIONS
with standard clean oven
Table of Contents
Advertisement
Table of Contents
Related Manuals for Whirlpool W10032070
Summary of Contents for Whirlpool W10032070
-
Page 1: Table Of Contents
INSTALLATION INSTRUCTIONS 30" (76.2 CM) FREESTANDING GAS RANGES RANGE SAFETY... 2 INSTALLATION REQUIREMENTS... 3 Tools and Parts... 3 Location Requirements... 4 Electrical Requirements... 5 Gas Supply Requirements... 6 INSTALLATION INSTRUCTIONS... 7 Unpack Range ... 7 Install Anti-Tip Bracket ... 7 Make Gas Connection... -
Page 2: Range Safety
Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER”... -
Page 3: Installation Requirements
In the State of Massachusetts, the following installation instructions apply: Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. If using a ball valve, it shall be a T-handle type. A flexible gas connector, when used, must not exceed 3 feet. -
Page 4: Location Requirements
IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the oven frame behind the left side of the broiler door. -
Page 5: Electrical Requirements
Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. If the cabinet depth is greater than 24" (61.0 cm), oven frame must extend beyond cabinet fronts by ½" (13.0 mm) minimum. IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for... -
Page 6: Gas Supply Requirements
WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. -
Page 7: Installation Instructions
Burner Input Requirements Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m). For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada). - Page 8 If cabinet opening is wider than that specified in the “Location Requirements” section, adjust template so range will be centered in cabinet opening. 5. To mount anti-tip bracket to wood floor, drill two holes at the positions marked on the bracket template. Remove template from floor and move to Step 7.
-
Page 9: Make Gas Connection
WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. -
Page 10: Verify Anti-Tip Bracket Location
5. Close the broiler door. 6. Remove cooktop burner caps and grates from parts package. Align notches in burner caps with pins in burner base. Burner caps should be level when properly positioned. If burner caps are not properly positioned, surface burners will not light. -
Page 11: Complete Installation
2. Insert a small flat-blade screwdriver into the valve stem. Turn the valve adjusting screw to obtain the smallest flame that will not go out when the control of a cold burner is quickly turned from “HI” to “Lo.” Turn right to decrease flame height. Turn left to increase flame height. -
Page 12: Gas Conversions
WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. - Page 13 To Convert Surface Burners 1. Remove burner grate, burner caps and burners. A. Burner cap B. Burner 2. Locate LP gas orifice spuds for top burners in the literature bag included with the range. Three LP gas spuds are stamped “88” and one “96.” 3.
-
Page 14: Complete Conversion
Complete Conversion 1. Refer to the “Make Gas Connection” section for properly connecting the range to the gas supply. 2. Turn the manual shutoff valve in the gas supply line to the open position. 3. Refer to “Check Operation” in the “Electronic Ignition System”... - Page 15 To Convert Surface Burners 1. Remove burner grate, burner caps and burners. A. Burner cap B. Burner 2. Locate the Natural gas orifice spuds for top burners in the literature bag included with the range. Three natural gas spuds are stamped “149” and one “165.” 3.
-
Page 16: Complete Conversion
3. Locate Natural gas orifice spud stamped “47” in the bag containing literature supplied with the range. 4. Use a " combination wrench and remove the LP gas orifice spud. 5. Install the number “47” LP gas spud. A. Natural gas oven orifice spud stamped with “47” IMPORTANT: Do not overtighten.