Setting The Timer - DeLonghi EL Series Instructions For Use Manual

SYMBOL WIFI FIXED
it means that the WiFi features are active AND the
"Home WLAN" has been found.
SLOW FLASHING
it means that the appliance is searching for the
"Home WLAN" .
FAST FLASHING
it means that the "Home WLAN" has not been
found or has not been set yet.
"APP CONTROL " ICON
When the APP CONTROL icon appears it means that
the last command has been received via app.
If the memorized "Home WLAN" settings needs to be changed,
proceed as follows:
a) keep touched for about 20 seconds the MODE button C2 on
the control panel until a prolonged beep is emitted;
b) use the app to enter the new WLAN settings into the unit.

SETTING THE TIMER

Timer programming is an exclusive function of the app: thanks
to the many possibilities of timer programming, you can prevent
wasting electricity by optimising the operating period, setting
delayed start up or shut down of the appliance.
FCC AND CANADA EMC COMPLIANCE
INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, includ-
ing interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which can
be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and re-
ceiver.
• Connect the equipment into an outlet on a circuit di erent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Approved under the certi cation provision of FCC Part 15 as a
Class B Digital Device.
Caution: Changes or modi cations not expressly approved by
the manufacturer could void the user's authority to operate
this device.
Caution: To comply with the limits of the Class B digital device,
pursuant to Part 15 of the FCC Rules, this device is to com-
ply with Class B limits. All peripherals must be shielded
and grounded. Operation with non-certi ed peripherals
or nonshielded cables my result in interference to radio or
reception.
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
WIRELESS TRANSMITTER COMPLIANCE INFORMATION
The term "IC:" before the radio certi cation number only signi-
es that Industry Canada technical speci cations were met.
Le terme «IC:» avant le numéro de certi cation radio signi e seulement
que les spéci cations techniques d'Industrie Canada ont été respectées.
This device complies with Industry Canada's licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada ap-
plicables aux appareils radio exempts de licence. L' e xploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage;
(2) l'utilisateur de l'appareil doit accepter tout brouillage ra-
dioélectrique subi, même si le brouillage est susceptible d' e n
compromettre le fonctionnement.
This equipment complies with FCC and IC radiation exposure
limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm
between the radiator and your body. This transmitter must not
be co-located or operating in conjunction with any other an-
tenna or transmitter.
Cet appareil est conforme à FCC et IC l' e xposition aux rayonnements
limites xées pour un environnement non contrôlé. Cet appareil
doit être installé et utilisé avec une distance minimale de 20 cm
entre le radiateur et votre corps.
11