Summary of Contents for Whirlpool Cabrio W10151492A
Page 1
Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com. Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.
Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER”...
INSTALLATION INSTRUCTIONS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Flat-blade screwdriver Tin snips (new vent installations) #2 Phillips screwdriver Level Adjustable wrench that opens to 1" (2.5 cm) or Vent clamps hex-head socket wrench Caulking gun and...
Installation spacing for recessed area or closet installation The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons: Additional spacing should be considered for ease of installation and servicing.
If your outlet looks like this: 3-wire receptacle (10-30R) Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.
Power Supply Cord WARNING Fire Hazard Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Ground wire (green or bare wire) must be connected to green ground connector.
Page 8
Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.
Page 9
1. Remove center silver-colored terminal block screw. 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw. A.
Page 10
3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw. A. External ground conductor screw B. Neutral ground wire C. Ground wire (green or bare) of power supply cord D. ¾" (1.9 cm) UL listed strain relief E.
Page 11
When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. 1. Loosen or remove center silver-colored terminal block screw. 2.
10.2 cm 4" (10.2 cm) heavy metal exhaust vent DURASAFE™ vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the “Assistance or Service” section. Rigid metal vent For best drying performance, rigid metal vents are recommended.
Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. A. Dryer E. Clamps B. Elbow F. Rigid metal or flexible metal vent C. Wall G. Vent length necessary to connect elbows D.
Vent system chart NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one elbow. To determine maximum exhaust length, add one elbow to the chart. Number of Type of Box or 90º turns vent Louvered or elbows hoods...
You can change your door swing from a right-side opening to a left-side opening, if desired. 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. Remove the door assembly 1. Open the dryer door. 2.
4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel. 5. Install screws in the top hinge holes in the door. Do not tighten screws.
WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Do not dry anything that has ever had anything flammable on it (even after washing). Failure to follow these instructions can result in death, explosion, or fire. WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
Adjust Dryness. NOTE: Dryness selections can be made only while using Automatic Cycles. How the AccelerCare™ Drying System Works Moisture-sensing strips and temperature sensors inside the dryer drum monitor how fast the load is drying, how hot the air should be and when clothes are dry. The system automatically stops the cycle to help save time and avoid overdrying.
Damp The Damp light illuminates in an Automatic Cycle when the laundry is approximately 80% dry. Damp Dry Signal beeps, if selected. See “Options.” Cool Down The Cool Down light illuminates during the cool down part of the cycle. Laundry cools for ease in handling. Done The Done light illuminates when the drying cycle is finished.
Modifiers Automatic Cycle Modifiers Use the Dryness Modifier to select dryness levels for the Auto Dry Cycles. Press DRYNESS until the desired Dryness setting illuminates. The preset dryness setting is Normal when an Automatic Cycle is selected. You can select a different dryness level, depending on your load, by pressing Dryness and choosing More, Normal, Less or Damp.
End of Cycle Signal End of Cycle Signal The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling. Press END OF CYCLE SIGNAL until the desired volume (Loud, Soft or Off) is selected.
7. You must select a time by pressing TIME ADJUST Up or Down. Reset time as needed to complete drying. Refer to the following table. 8. Press (and hold) START button (about 1 second). This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time.
4. Use masking tape to secure dryer door. First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) In U.S.A. www.whirlpool.com/help - In Canada www.whirlpool.ca Dryer will not run Has a household fuse blown, or has a circuit breaker...
Page 24
“L2” Diagnostic Code (low or no line voltage condition): The drum will turn, but there may be a problem with your home power supply keeping the dryer's heater from turning on. The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display and return to the estimated time remaining.
Canada. For further assistance If you need further assistance, you can write to Whirlpool Canada LP with any questions or concerns at: Customer Interaction Centre Whirlpool Canada LP...
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité...
INSTRUCTIONS D’INSTALLATION Outillage et pièces Rassembler les outils et pièces nécessaires avant de commencer l’installation. Lire et suivre les instructions fournies avec les outils indiqués ici. Tournevis à lame plate Niveau Tournevis Phillips n Clapets d’évacuation Clé à molette avec Pistolet à...
14" max.* (35,6 cm) 18"* (45,7 cm) 1" 29" 1" 1"* 29¼" 5" (2,5 cm) (2,5 cm) (73,7 cm) (2,5 cm) (74,3 cm) (12,7 cm) A. Encastrement B. Vue latérale – placard ou endroit exigu C. Porte du placard avec orifices d’entrée d’air *Espacement requis Exigences supplémentaires pour l’installation dans une maison mobile...
Page 31
Conduit d'évacuation en métal lourd de 4" (10,2 cm) On peut se procurer les produits d’évacuation DURASAFE™ auprès du marchand ou en téléphonant au service Pièces et accessoires de Whirlpool. Pour plus de renseignements, voir la section “Assistance ou service”. Conduit métallique rigide Pour un meilleur rendement de séchage, on recommande...
Choisir un type de système d’évacuation Installations d’évacuation recommandées Les installations typiques consistent à acheminer le conduit d’évacuation à l’arrière de la sécheuse. A. Sécheuse F. Conduit métallique rigide ou flexible B. Coude G. Longueur de conduit nécessaire pour raccorder les coudes C.
Tableau des systèmes d'évacuation REMARQUE : L’évacuation par l’arrière (côté gauche ou droit) fonctionne en ajoutant un coude. Pour établir la longueur maximale du conduit, ajouter un coude supplémentaire dans le tableau. Nombre de Type de Clapets de change- conduit type boîte ou ments de à...
Si la sécheuse n'est pas d'aplomb, la relever à l'aide d'un bloc de bois. Utiliser une clé pour ajuster les pieds vers le haut ou vers le bas, et vérifier à nouveau si elle est d'aplomb. Inversion du sens d'ouverture de la porte Le sens d'ouverture de la porte peut être changé...
3. Retirer les quatre vis du côté opposé de la porte. 4. Installer les deux charnières sur le panneau avant de la sécheuse à l'aide de quatre vis. Utiliser le côté sans fente pour fixer la charnière sur le panneau avant. 5.
UTILISATION DE LA SÉCHEUSE AVERTISSEMENT Risque d'explosion Garder les matières et les vapeurs inflammables, telle que l’essence, loin de la sécheuse. Ne pas faire sécher un article qui a déjà été touché par un produit inflammable (même après un lavage). Le non-respect de ces instructions peut causer un décès, une explosion ou un incendie.
Le réglage de séchage par défaut est Normal lorsqu'on sélectionne un programme automatique. On peut sélectionner un degré de séchage différent, en fonction de la charge, en appuyant sur Dryness et en choisissant More (plus), Less (moins) ou Damp (humide). La sélection de More (plus), Less (moins) ou Damp (humide) ajuste automatiquement la durée détectée nécessaire.
Conseils pour les programmes On recommande de sécher la plupart des charges en utilisant les préréglages de programme. Consulter le tableau des préréglages des programmes automatiques ou minutés (à la section “Programmes”) pour un guide de séchage de charges diverses. La température de séchage et le degré...
Delicate (articles délicats) Utiliser ce programme pour le séchage à température extra basse des articles tels que la lingerie, les chemisiers et les tricots lavables. Préréglages des programmes automatiques Programmes automatiques Type de charge HEAVY DUTY (service intense) Charges mixtes lourdes, articles en coton, jeans NORMAL Velours côtelé, vêtements de travail...
Air Only (air seulement) Utiliser le modificateur Air Only pour les articles qui doivent être séchés sans chaleur, tels que le caoutchouc, le plastique et les tissus sensibles à la chaleur. Ce tableau donne des exemples d'articles qui peuvent être séchés au réglage Air Only. Type de charge Caoutchouc mousse - oreillers, soutiens-gorge rembourrés, jouets rembourrés...
Changement des programmes, modificateurs et options Il est possible de changer les programmes automatiques et minutés, les modificateurs et les options à tout moment avant d'appuyer sur le bouton Start (mise en marche). Trois brefs signaux sonores marquent le choix d'une combinaison non disponible.
REMARQUE : Ne pas laisser un article pendre par-dessus le bord de la grille. 4. Fermer la porte. 5. Appuyer sur le bouton POWER (alimentation). 6. Sélectionner un programme de séchage minuté et une température (voir tableau suivant). Les articles contenant de la mousse, du caoutchouc ou du plastique doivent être séchés sur une corde à...
Nettoyage au besoin 1. Enlever la charpie du filtre en la roulant avec les doigts. 2. Mouiller les deux côtés du filtre à charpie avec de l'eau chaude. 3. Mouiller une brosse en nylon avec de l'eau chaude et du détergent liquide.
Essayer d’abord les solutions suggérées ici ou visiter notre site Web et consulter les références FAQ (Foire Aux Questions), ce qui vous évitera peut-être le coût d’une visite de service...www.whirlpool.ca Fonctionnement de la sécheuse Le sécheuse ne fonctionne pas Un fusible est-il grillé ou le disjoncteur s'est-il déclenché? Il peut y avoir 2 fusibles ou disjoncteurs pour la sécheuse.
Page 45
AVERTISSEMENT Risque d’incendie Utiliser un conduit d’évacuation en métal lourd. Ne pas utiliser un conduit d’évacuation en plastique. Ne pas utiliser un conduit d’évacuation en feuille de métal. Le non-respect de ces instructions peut causer un décès ou un incendie. Le conduit d'évacuation ou le clapet d'évacuation à...
Les références aux concessionnaires, compagnies de service de réparation et distributeurs de pièces de rechange locaux. Les techniciens de service désignés par Whirlpool Canada LP sont formés pour remplir la garantie des produits et fournir un service après la garantie, partout au Canada.
CONFÈRE DES DROITS JURIDIQUES SPÉCIFIQUES ET VOUS POUVEZ ÉGALEMENT JOUIR D'AUTRES DROITS QUI PEUVENT VARIER D'UNE JURIDICTION À UNE AUTRE. À l'extérieur du Canada et des 50 États des États-Unis, cette garantie ne s'applique pas. Contacter votre marchand Whirlpool autorisé pour déterminer si une autre garantie s'applique.
Page 48
® Registered Trademark/TM Trademark of Whirlpool, U.S.A., Whirlpool Canada LP Licensee in Canada Printed in U.S.A. Tous droits réservés. ® Marque déposée/TM Marque de commerce de Whirlpool, U.S.A., emploi sous licence par Whirlpool Canada LP au Canada Imprimé aux É.-U.