Saving Energy - Whirlpool AR1800XA0 Installation & User Manual

Whirlpool room air conditioner installation & user's guide room air conditioner
Table of Contents

Advertisement

5.
6.
7.
8.
Carefully clean and hose-out the base, condenser coils,
and condensate
pans. Clean at least once a year, or more
often if the condenser coil and pan collect dirt, sand,
leaves, insects or algae. Also clean if you detect an odor
coming from the air conditioner.
Remove the plastic film from the motor and electrical parts.
Replace air conditioner
in the cabinet.
Replace the front panel.
. Push front panel straight onto cabinet. Then lower it
slightly to lock it in place.
l
Replace the two screws in the base of the front
panel.
9. Plug in power cord.
NOTE: It is a good idea to wait 24 hours before starting the
unit again. This allows time for all areas to dry thoroughly.
Repairing
paint
damage
Check once or twice a year. This is very important, especially
in areas near oceans or where rust is a problem. If needed,
touch up with a good grade enamel paint.
Saving
energy
You can help save energy by doing the followtng.
l
Improve your home's insulation. Seal doors and windows.
Close fireplace flues.
l
Close blinds or drapes on the sunny side of the house, Add
awnings.
l
Check air filter often to make sure it is clean.
l
Do not block airflow with drapes or furniture.
. Ventilate your attic. High temperatures
in the attic add to the
cooling load of your air conditioner.
l
Try not to use heat-producing
appliances
during the hottest
part of the day.
l
Turn lights and appliances
off when they are not needed.
l
Keep heat registers and cool-air returns closed.
l
Use exhaust/venting
fans while cooling, bathing and doing
laundry
l
Turn your System Control to OFF if you will be away for a
long time. The air conditioner will not come on again until the
System Control is set to a COOL or HEAT setting.
Cuidadosamente
limpiar y echar un chorro de agua con
manguera a la base y a 10s serpentines
del condensador
y
10s colectores del condensador.
Limpiar por lo menos una
vez al ano o mas a menudo si 10s serpentines
del
condensador
y las bandejas coleccionan
suciedad, arena,
hojas, insectos o algas. Tambien limpiar si usted detecta
que sale mal olor del acondicionador
de aire.
Quitar el plastic0 que cubre el motor y las piezas electricas.
Volver a colocar el acondicionador
de aire en la caja
metalica.
Volver a colocar el panel delantero.
l
Empujar el panel delantero derecho en la caja. Luego
hacerlo descender para que calce en su lugar.
l
Volver a colocar 10s dos tornillos en la base del panel
delantero.
Enchufar el cable electrico.
NOTA: Es una buena idea esperar 24 horas antes de volver a
poner en funcionamiento
el acondicionador
de aire. Esto
permite que todas las piezas se sequen completamente.
Reparacibn
de la pintura
dairada
Revisar una o dos veces al ano. Esto es muy importante
especialmente
en regiones cerca del ocean0 o donde existen
problemas de oxidation.
Si es necesario, retocar con un
esmalte de buena calidad.
Ahorro
de energia
Usted puede ayudar a ahorrar enersa
de la siguiente manera.
l
Mejorar el aislamiento
de su hogar. Sellar las puertas y
ventanas. Cerrar 10s tubos de humo de la chimenea.
l
Cerrar las cortinas o persianas en el lado asoleado de la
casa.
. lnstalar toldos
l
Revisar el filtro de aire a menudo para asegurarse
de que
este limpio.
l
No bloquear el flujo del aire con cortinas o muebles
l
Ventilar el desvan. Las altas temperaturas
en el desvan
contribuyen
a la carga de enfriamiento
de su acondicionador
de aire.
l
Tratar de no usar artefactos que producen calor durante el
period0 mas caluroso del dia.
9 Apagar las lutes y 10s artefactos electricos cuando no estan
en uso.
l
Mantener cerrados 10s registros de la calefaccion y 10s
conductos de retorno del aire frio.
l
Usar ventiladores
de escapeicirculacion
cuando se esta
batiando, lavando ropa o enfriando.
l
Colocar el Control del Sistema en la position OFF si va a
estar ausente por un period0 de tiempo largo. El
acondicionador
de aire no funcionara nuevamente
hasta que
el Control del Sistema sea puesto en la position COOL o
HEAT.
34

Advertisement

Table of Contents
loading

Table of Contents