Table of Contents
Advertisement
Quick Links
707
OPERATION MANUAL
WATER-MAX II™
WM-TR II™
HOT WATER
DISPENSER
Includes
INSTALLATION
USE & CARE
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions
concerning installation,
PRINTED IN UNITED STATES OF AMERICA
306692
06
p/n
Rev. A
ECN-13060
M707
0418 cps
Advertisement
Table of Contents
Related Manuals for Wells WM-TR II
Summary of Contents for Wells WM-TR II
- Page 1 MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of this appliance. Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation,...
- Page 2 Seller’s obligation under this warranty is limited to the repair of defects without charge by a Wells Mfg. Co. factory authorized service agency or one of its sub-service agen- cies.
-
Page 3: Table Of Contents
PARTS & SERVICE CUSTOMER SERVICE DATA Thank you for purchasing this Wells Manufacturing Co. appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life. -
Page 4: Features & Operating Controls
FEATURES & OPERATING CONTROLS 4 HEAT (AMBER) 3 REFILL (AMBER) 2 POWER (GREEN) WELLS Fig. 1 Features & Operating Controls - Water Max II™ Hot Water Dispenser ITEM DESCRIPTION HEATER SWITCH POWER LIGHT REFILL LIGHT HEAT LIGHT FLOW NOZZLE SATELLITE SWITCH... - Page 5 COVER HANDLE NAMEPLATE S8 SATELLITE CONNECTOR S7 BACK VIEW Fig. 2 Features & Operating Controls - Water Max II™ 5 Gallon Satellite ITEM DESCRIPTION COVER COVER HOLDING CLIPS Retains cover in place WATER LEVEL SENSOR Maintains water level in tank DISPENSE FAUCET FAUCET GUARD HANDLE...
-
Page 6: Precautions & General Information
PRECAUTIONS AND GENERAL INFORMATION WARNING: Electric Shock hazard All servicing requiring access to non-insulated electrical components must be performed by a factory authorized technician. DO NOT open any access panel which requires the use of tools. Failure to follow this warning can result in severe electrical shock. -
Page 7: Installation
UNPACKING & INSPECTION Carefully remove the appliance from the carton. Remove all protective plastic film, packing materials and accessories from the appliance before connecting electrical power or otherwise performing any installation procedure. Carefully read all instructions in this manual and the Installation Instruction Sheet packed with the appliance before starting any installation. - Page 8 INSTALLATION (continued) CAUTION: RISK OF DAMAGE DO NOT connect or energize this appliance until all Installation Instructions are read and followed. Damage to the dispenser will occur if these instructions are not followed. IMPORTANT: Water supply MUST be a minimum of 1/4” line, and MUST be capable of supplying 25 p.s.i.
- Page 9 ELECTRICAL INSTALLATION NOTICE: A DEDICATED CIRCUIT OF AT LEAST 40 AMPS IS REQUIRED. WIRING AND CONNECTIONS MUST BE INSTALLED AND MAINTAINED IN COMPLIANCE WITH FEDERAL, STATE, AND LOCAL ORDINANCES. The dispenser is factory configured for either 208 volts or 240 volts. The voltage configuration is NOT field convertible.
- Page 10 INSTALLATION (continued) CAUTION: Hot Surface Exposed surfaces can be hot to the touch and may cause burns. CAUTION Burn Hazard Water in Water-Max II™ is EXTREMELY HOT! CAUTION SCALDING HAZARD Place satellite tank on dispenser as soon as the main tank is at temperature (i.e.
-
Page 11: Operation
Water-Max II™ is used to dispense hot water for food preparation. The SATELLITE TANK stores five gallons of hot water for immediate use. INSTALLING OR REMOVING SATELLITE TANK Drain all water from SATELLITE before attempting to remove from unit. Press the HEATER SWITCH to Be sure the COVER is properly installed on the SATELLITE Install or remove SATELLITE on Water-Max II™... -
Page 12: Cleaning Instructions
CLEANING INSTRUCTIONS CAUTION: BURN HAZARD Water in satellite is extremely hot. Use care when draining. CAUTION: HOT SURFACES Exposed surfaces can be hot to the touch and may cause burns. CAUTION: EQUIPMENT DAMAGE DO NOT SUBMERGE SATELLITE IN WATER! IMPORTANT: DO NOT use bleach, abrasive cleansers or cleansers containing... - Page 13 PRECAUTIONS: Water in main tank is EXTREMELY HOT (around 200ºF) FREQUENCY: Weekly TOOLS: Wells Deliming Solution Bottle (p/n 85377) Plastic Scouring Pad Clean Cloth or Sponge Kay Orange Neutralizer and Delimer (Kay p/n 55905) Begin with the HEATER SWITCH temperature (i.e. HEAT light not lit), and with SATELLITE full of hot water.
- Page 14 CLEANING INSTRUCTIONS (continued CAUTION Burn Hazard Water in Water-Max II™ is EXTREMELY HOT! Wear appropriate heat protective clothing when draining water from unit. IMPORTANT: Never drain internal tank with HEATER SWITCH Tank heating element will be damaged if allowed to operate without water.
- Page 15 PERIODIC CLEANING - Satellite Tank PRECAUTIONS: Water in satellite is EXTREMELY HOT (around 200ºF) Satellite full of water is HEAVY (62 lbs.) Drain water from SATELLITE before moving. FREQUENCY: Weekly TOOLS: Plastic Scouring Pad Clean Cloth or Sponge Kay Orange Neutralizer and Delimer (Kay p/n 55905) Press HEATER SWITCH to OFF [ O ].
-
Page 16: Troubleshooting Suggestions
Dispensed water not hot enough Main tank does not heat There are no user serviceable components in the appliance. In all cases of damage or component malfunction, contact your Authorized Wells Service Agency for repairs. POSSIBLE CAUSE Circuit breaker off or tripped... -
Page 17: Parts & Service
IMPORTANT: Use only factory authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Manufacturing Co. 2 Erik Circle P. O. Box 280 Verdi, NV 89439... - Page 18 PRINTED IN UNITED STATES OF AMERICA...