Table of Contents
Advertisement
Model No. WESY91080
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
USERÕS
MANUAL
PATENT PENDING
¨
Advertisement
Table of Contents
Related Manuals for Weider WESY91080
Summary of Contents for Weider WESY91080
- Page 1 Model No. WESY91080 Serial No. The serial number is found in the location shown below. Write the serial number in the space above. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you...
- Page 2 Table of Contents Important Precautions ..............2 Before You Begin .
- Page 3 Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is WESY91080. The serial number can be found on a decal attached to the WEIDER System (see the front cover of this manual).
- Page 4 Assembly Note: This introduction will save you more time than it takes to read it! Making Things Easier for Yourself Everything in this manual is designed to ensure that the assembly of our products can be complet- ed successfully by anyone. However, it is impor- tant to recognize that your new equipment is a sophisticated product with many small parts.
- Page 5 Frame Assembly 1. Before beginning, be sure that you have read and understood the information on page 4. Locate and open the parts bag labeled ÒFRAME ASSEMBLY.Ó Press a 2Ó Square Cover Cap (78) onto each end of the Stabilizer (5). Insert two 3/8Ó...
- Page 6 5. Press a 1Ó Square Inner Cap (65) into the side arm (A) on the Press Upright (56). Slide the Press Upright (56) onto the 5/16Ó x 2 1/2Ó Carriage Bolts (1) in the Press Base (51). Hand tight- en a 5/16Ó Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet.
- Page 7 7. Set two Weight Bumpers (19) onto the bracket on the Stabilizer (5). Insert both Weight Guides (62) through the Weight Bumpers and the bracket on the Stabilizer (5). Attach the lower ends of the Weight Guides (62) to the Stabilizer (5) with a 3/8Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó...
- Page 8 10. Place the Top Frame (55) on top of the two Uprights (56) and (42) in the direction shown. Align the holes in the Top Frame with the holes in the brackets on the Uprights. Insert four 5/16Ó x 2 3/4Ó Bolts (11) with four 5/16Ó Flat Washers (8) through the holes in the Top Frame (55) and the brackets on the Uprights.
- Page 9 14. Press a 1 3/4Ó Square Inner Cap (44) into the lower end of each Press Arm (46). Press a 1Ó Round Inner Cap (49) into the side of each Press Arm. Attach each Press Arm to the Press Frame (17) with two 5/16Ó...
- Page 10 16. Lubricate both axles (A) on the Top Frame (55). Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right and Left Arm. Make sure the upper end of the Right Arm is behind the indicated bracket (B) on the Top Frame.
- Page 11 19. Attach two 3 1/2Ó Pulleys (15) to the weight support arm (A) on the Top Frame (55) with two 3/8Ó x 2Ó Bolts (12) and two 3/8Ó Nylon Locknuts (21). 20. Locate the Short Cable (23). It has a ball on one end and a threaded tip on the other.
- Page 12 23. Move to the other side of the unit. Route the Short Cable (23) through the second 3 1/2Ó Pulley (15) on the weight support arm. Make sure the Short Cable (23) is in the groove of all Pulleys and that the Cable and the Pulleys move smoothly.
- Page 13 26. Attach a ÒVÓ-Pulley (6) and a Long Cable Trap (50) to the bracket on the Press Seat Frame (77) with a 3/8Ó x 2 1/2Ó Bolt (7) and a 3/8Ó Nylon Locknut (21). It may be necessary to place the Long Cable Trap on top of the bracket.
- Page 14 29. Move to the other side of the unit. Route the Long Cable (58) around the second 3 1/2Ó Pulley (15) on the Leg Press Arm (89) in the direction shown. 30. Route the Long Cable (58) around the 3 1/2Ó Pulley (15) on the Butterfly Base (4).
- Page 15 33. Remove the 3 1/2Ó Pulley (15) from the Long ÒUÓ- Bracket (57). Route the Medium Cable (86) around the Pulley in the direction shown. Re-attach the Pulley to the Long ÒUÓ-Bracket (57) with the 3/8Ó x 2Ó Bolt (12) and the 3/8Ó Nylon Locknut (21).
- Page 16 37. Attach the other end of the Seat (13) to the Press Seat Frame (77) with a 1/4Ó Flat Washer (10) and a 1/4Ó x 2 1/2Ó Screw (43). 38. Move to the other end of the unit. Attach the remain- ing Backrest (41) to the Butterfly Upright (42) with two 1/4Ó...
- Page 17 40. Press a 1 1/2Ó Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the Bolt and a 5/16Ó Nylon Locknut (3). Do not overtighten the Nylon Locknut.
- Page 18 44. Attach the Adjustment Tube (88) to the Leg Press Arm (89) with the Small Lock Pin (90). Make sure the Leg Press Plate (87) is oriented as shown. 45. Remove the decals from the decal sheets (not shown) and apply them to the home gym system in the loca- tions shown in the illustration below.
- Page 19 46. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 20 of this manual. Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys.
- Page 20 Adjustment The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor- rect starting position for the exercise to be performed.
- Page 21 Attaching the Lat Bar or Nylon Strap to the Low Pulley Station Attach the Lat Bar (54) to the Medium Cable (86) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the Long Cable with two Cable Clips.
- Page 22 Weight Resistance Chart This chart shows the approximate weight resistance at each station. ÒTopÓ refers to the 6.5 lbs. top weight. The other numbers refer to the 12.5 lbs. weight plates. Note: The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides.
- Page 23 Trouble-shooting and Maintenance Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the Cables Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used.
- Page 24 1/4" Nylon Locknut (2) 1/4" x 2" Carriage Bolt (38) 5/16" Nylon Locknut (3) 1/4" x 2 1/2" Screw (43) 3/8" Nylon Jam Nut (83) 1/4" x 2 1/2" Carriage Bolt (91) 3/8" Nylon Locknut (21) 1/4" Flat Washer (10) 1/4"...
- Page 25 3/4" Round Inner Cap (34) 1" Round Inner Cap (49) 1" Round Cover Cap (70) 5/16" x 2" Eyebolt (35) 1" Square Inner Cap (65) 1 3/4" Square Inner Cap (44) 2" Square Cover Cap (78) 2" Square Inner Cap (27) 1 1/2"...
- Page 26 3/8" x 2" Bolt (12) 5/16" x 2 1/4" Bolt (33) 3/8" x 2 1/2" Bolt (7) 5/16" x 2 1/2" Bolt (22) 3/8" x 2 3/4" Bolt (93) 3/8" x 2 3/4" Carriage Bolt (94) 3/8" x 3 1/4" Bolt (85) 3/8"...
- Page 28 Part ListÑModel No. WESY91080 Key No. Qty. Description 5/16Ó x 2 1/2Ó Carriage Bolt 1/4Ó Nylon Locknut 5/16Ó Nylon Locknut Butterfly Base Stabilizer ÒVÓ-Pulley 3/8Ó x 2 1/2Ó Bolt 5/16Ó Flat Washer 3/8Ó Flat Washer 1/4Ó Flat Washer 5/16Ó x 2 3/4Ó Bolt 3/8Ó...
- Page 29 This warranty gives you specific legal rights. You may also have other rights which vary from state to state. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813 WEIDER is a registered trademark of ICON Health & Fitness, Inc. Part No. 147977 H01996-C R0998A ¨...