Weider WESY49310 User Manual

Weider fitness user's manual weight system wesy49310

Advertisement

Model No. WESY49310
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that there
are missing or damaged parts,
we will guarantee you complete
satisfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.

TABLE OF CONTENTS

Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
How To Use The Weight System . . . . . . . . . . . . . . . . . . . .22
Weight Resistance Chart . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLE-SHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . .25
Cable Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Ordering Replacement Parts . . . . . . . . . . . . . . .Back Cover
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/
Exploded Drawing are attached in the center of this manual.
USER'S MANUAL

Advertisement

Table of Contents
loading

Summary of Contents for Weider WESY49310

  • Page 1 Model No. WESY49310 Serial No. Write the serial number in the space above for reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there...
  • Page 2: Important Precautions

    IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
  • Page 3: Product View

    (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is WESY49310. The serial number can be found on a decal attached to the weight system (see the front cover of this manual).
  • Page 4: Assembly

    ASSEMBLY Before beginning assembly, carefully read the following information and instructions: • Place all parts of the weight system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • The assembly is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly.
  • Page 5 2. Slide the Assist Upright (74) and the Leg Press Upright (56) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Uprights should be on the side shown. Hand-tighten four 5/16”...
  • Page 6 4. Press a 2” Square Inner Cap (27) into the end of the Top Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the Top Frame. Press two 1” Inner Caps (113) into the top of the crossbar. Attach the Top Frame (55) to the Assist Upright (74) and the Leg Press Upright (56) with two 5/16”...
  • Page 7 7. Press a Weight Tube Bumper (64) into the end of the Short Weight Tube (108). Insert the Weight Tube into the front stack of Weights (25). Be sure that the pin on the Weight Tube is sitting in the pin grooves in the top Weight.
  • Page 8 9. Attach the upper ends of the Short Weight Guides (73) to the Top Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the Top Frame (55) in the same manner.
  • Page 9 12. Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16”...
  • Page 10 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the Military Press Arm (84). Press two 1” Round Inner Caps (49) into the Military Press Arm.
  • Page 11 17. Attach the Left Pull-up Arm (75) and the Right Pull-up Arm (77) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (11) and two 5/16” Nylon Locknuts (3). Attach the Left Dip Arm (78) and the Right Dip Arm (79) to the Assist Upright (74) with two 5/16”...
  • Page 12 20. Wrap the High Cable (58) around a “V”-Pulley (50). Attach the “V”-Pulley and a Long Cable Trap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable Trap is positioned to hold the Cable in place.
  • Page 13 24. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable Trap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is inside the Long “U”- Bracket.
  • Page 14 27. Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (102). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame.
  • Page 15 31. Attach the end of the Low Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing.
  • Page 16 34. Wrap the Military Press Cable (72) around a “V”-Pulley (50). Attach the “V”-Pulley to the Top Frame (55) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Wrap the Military Press Cable (72) around a 3 1/2”...
  • Page 17 36. Slide a 5/16” Flat Washer (8) onto a 5/16” x 2 3/4” Bolt (11). Insert the Bolt through the indi- cated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tighten a 5/16” Nylon Jam Nut (93) onto the Bolt.
  • Page 18 38. Locate the Leg Press Cable (99). Attach the end of the Leg Press Cable to the Long “U”- Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.
  • Page 19 40. Locate and open the parts bag labeled “SEAT ASSEMBLY.” Insert a 1/4” x 2 1/2” Carriage Bolt (92) through the center hole in a Seat Plate (37). Attach the Seat Plate to the Rear Backrest (85) with two 1/4” x 3/4” Screws (18). Insert the 1/4”...
  • Page 20 43. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat Washers (10). The Backrest must be oriented as shown. 44. Press a 1 1/2” Square Inner Cap (32) into the Front Seat Frame (36).
  • Page 21 Insert the other Pad Tube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto each end of the Pad Tube. 48. Remove the backing from the CLUB WEIDER ® 17.0ST decal and apply it to the weight system where shown.
  • Page 22: How To Use The Weight System

    HOW TO USE THE WEIGHT SYSTEM The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise poster accompanying this manual to see how the weight system should be set up for each exercise. IMPOR- TANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct start- ing position for the exercise to be performed.
  • Page 23 ATTACHING AND REMOVING THE SEAT To attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Front Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).
  • Page 24: Weight Resistance Chart

    WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
  • Page 25: Trouble-Shooting And Maintenance

    TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used.
  • Page 26: Cable Diagrams

    CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly.
  • Page 27 Military Press Cable (72) and Leg Press Cable (99) Military Press Cable (72) 8—Pivot Arm 1—Long “U”-Bracket Rear Weight Stack—1 4—Rear Seat Frame Leg Press Cable (99)
  • Page 28 WESY49310 R0901A 1/4" Nylon Locknut (2) 1/4" x 2" Machine Screw (81) 5/16" Nylon Locknut (3) 1/4" x 2 1/2" Carriage Bolt (92) 5/16" Nylon Jam Nut (93) 5/16" x 2 1/2" Bolt (22) 3/8" Nylon Locknut (21) 3/8" x 2" Bolt (12) 1/4"...
  • Page 29 5/16" x 3" Bolt (111) 3/8" x 3 1/4" Bolt (67) 3/8" x 3 1/2" Bolt (16) 1/4" x 3/4" Screw (18) 3/8" x 3 3/4" Bolt (88) 5/16" x 5" Bolt (68) Cable Clip (53) 1" Retainer (69) 1 1/8" x 2 1/2" Plastic Bushing (89) 1"...
  • Page 30 5/16" x 2" Eyebolt (35) 1/2" x 3/4" Spacer (61) 5/8" x 9/16" Spacer (7) 3/4" Round Inner Cap (34) 1" Round Inner Cap (49) 1" Round Cover Cap (70) 1" Inner Cap (113) 1 1/2" Square Inner Cap (32) 1"...
  • Page 31 PART LIST—Model No. WESY49310 Key No. Qty. Description 5/16” x 2 1/2” Carriage Bolt 1/4” Nylon Locknut 5/16” Nylon Locknut Base Stabilizer 1” Square Inner Cap 5/8” x 9/16” Spacer 5/16” Flat Washer 3/8” Flat Washer 1/4” Flat Washer 5/16” x 2 3/4” Bolt 3/8”...
  • Page 32 EXPLODED DRAWING—Model No. WESY49310 R1101A...
  • Page 33: Ordering Replacement Parts

    This warranty gives you specific legal rights. You may also have other rights which vary from state to state. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813 WEIDER is a registered trademark of ICON Health & Fitness, Inc. Part No. 175066 R1101A ®...

This manual is also suitable for:

Club 17.0st

Table of Contents