Table of Contents
Advertisement
Quick Links
BHM
10/26/16
NTV-DOC270
th
3950 NW 120
Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760
www.nav-tv.com
info@nav-tv.com
GM-LVDS
NTV-KIT780
Overview
The GM-LVDS interfaces a backup camera input (and 1 additional video input) to the factory
media screen in select GM vehicles equipped with either the MYLINK or CUE (8" only) media
systems. With additional parts, HDMI input or Navigation is available with this unit (available
soon). Audio integration uses the OEM AUX input if adding an A/V source).
Kit Content
Cadillac
LVDS Input cable
Harness
Chevy/GMC
Harness
GM-LVDS Interface
LVDS Output cable
Power/CAN Harness
IR Eye Harness
OSD Menu Remote
:
Agreement
End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 |
P a g e
Advertisement
Table of Contents
Related Manuals for Nav TV GM-LVDS
Summary of Contents for Nav TV GM-LVDS
- Page 1 NTV-KIT780 Overview The GM-LVDS interfaces a backup camera input (and 1 additional video input) to the factory media screen in select GM vehicles equipped with either the MYLINK or CUE (8” only) media systems. With additional parts, HDMI input or Navigation is available with this unit (available soon).
- Page 2 10/26/16 NTV-DOC270 Interface Connectors Video Expansion board plug Not Used OUOUT LVDS OUT LVDS IN Digital RGB (HMDI/NAV) Power/CAN (to screen) (from HMI) requires adapter (coming soon) OUOUT NOT USED NOT USED Dip Switches Touch data connection (power harness) Dip Switch Settings* Configure prior to installation Dip SW: Chevy/ Keep...
- Page 3 Harness or Cadillac T-Harness (only 1 is used per install) and LVDS Input Cable. The other end of these cables get connected to the GM-LVDS interface via the provided Power/CAN Harness and directly to the LVDS IN connector. 5. Connect the provided LVDS Output Cable from the ‘video out’...
- Page 4 10/26/16 NTV-DOC270 GM-LVDS Operation After all connections are made and dip switches set properly, start the vehicle. Placing the vehicle in reverse will show the connected rear camera, with dynamic guidelines overlaid onto the media screen. If adding a front camera, this must be activated in the OSD menu (see page 5) or by setting DIP SWITCH #2 to ON.
- Page 5 10/26/16 NTV-DOC270 Setting/Navigating OSD Menu Before you start: The IR-Eye must be connected Make sure the car’s ignition is on and radio is on You must be in Reverse Camera mode AUX Video mode (see Return (AUX VID below): ...
- Page 6 10/26/16 NTV-DOC270 OSD Menu Options (continued) BT-CALL: How a (OEM setup) Bluetooth phone call is handled while in AV/HDMI mode: o ON - When in AV/NAV mode, the unit will transition to the OEM screen when a Bluetooth phone call is active, then return when call is ended. o OFF - There is no screen transition when a BT call is active.
- Page 7 10/26/16 NTV-DOC270 GM-LVDS Connection Diagram Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only.
- Page 8 10/26/16 NTV-DOC270 GM-LVDS FAQ 1. I’ve installed this interface properly, now I have a black screen all the time. a. Make certain the IN and OUT LVDS video cables are connected in the proper location (at the screen and proper direction), and seated fully. The ‘OUT’ cable should go directly to the screen, and the ‘IN’...
Need help?
Do you have a question about the GM-LVDS and is the answer not in the manual?
Questions and answers