Do you have a question about the TWIST-N-EDGE 530088832 and is the answer not in the manual?
Questions and answers
Kristine Zielke
June 2, 2025
How to change the string on my weedeater weedeater
1 comments:
Mr. Anderson
June 2, 2025
To change the string on a Weed Eater TWIST-N-EDGE 530088832:
1. Insert the line into the notch on the spool, leaving 3 to 5 inches (7–12 cm) unwound. 2. Insert the line into the exit hole in the hub as shown in the illustration. 3. Align the notch with the line exit hole. 4. Push the spool into the hub until it snaps into place. 5. Pull the line extending outside of the hub to release it from the notch.
This answer is automatically generated
Ben W Wakefield Jr
February 28, 2025
How do I get the spool out so I can refill it with string?
1 comments:
Mr. Anderson
February 28, 2025
To remove the spool from a Weed Eater TWIST-N-EDGE 530088832, firmly pull on the tap button of the spool until it comes off.
This answer is automatically generated
Related Manuals for Weed Eater TWIST-N-EDGE 530088832
Summary of Contents for Weed Eater TWIST-N-EDGE 530088832
Page 1
Please do not return unit to retailer. Por favor, no devuelva el aparato al lugar de compra. Veuillez ne pas retourner l’outil au détaillant. 1-800-554-6723 www.weedeater.com Operator’s Manual Manual del Operador Manuel de L’utilisateur For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating Instructions before using this product.
S Maintain unit according to recommended procedures. Keep cutting line at proper length. S Use only 0.080” (2 mm) diameter Poulan/ Weed Eater! brand line. Never use wire, rope, string, etc. S Install required shield properly before using the unit. Use only specified trimmer head;...
S Always store gasoline in a container ap- proved for flammable liquids. CUTTING SAFETY WARNING: Inspect the area before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by line or become entangled. Hard objects can damage trimmer head and be thrown causing serious injury.
2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand oil is recom- mended. (A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline).
Page 5
Line in Notch Line exit hole S Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool. S Push the line into the notch, leaving 3 to 5 inches (7 -- 12 cm) unwound. S Insert the line into the the exit hole in the hub as shown in the illustration.
PRODUCTS NORTH AMERICA, Division of WCI Out- door Products, Inc., warrants to the original purchaser that each new Weed Eater brand gasoline tool or attachment is free from de- fects in material and workmanship and agrees to repair or replace under this war-...
Page 7
REPLACEMENT OF PARTS. Repair or re- placement of any warranted part will be per- formed at no charge to the owner at an ap- proved POULAN/WEED EATER servicing center. If you have any questions regarding your warranty rights and responsibilities, you...
Need help?
Do you have a question about the TWIST-N-EDGE 530088832 and is the answer not in the manual?
Questions and answers
How to change the string on my weedeater weedeater
To change the string on a Weed Eater TWIST-N-EDGE 530088832:
1. Insert the line into the notch on the spool, leaving 3 to 5 inches (7–12 cm) unwound.
2. Insert the line into the exit hole in the hub as shown in the illustration.
3. Align the notch with the line exit hole.
4. Push the spool into the hub until it snaps into place.
5. Pull the line extending outside of the hub to release it from the notch.
This answer is automatically generated
How do I get the spool out so I can refill it with string?
To remove the spool from a Weed Eater TWIST-N-EDGE 530088832, firmly pull on the tap button of the spool until it comes off.
This answer is automatically generated