Subscribe to Our Youtube Channel
Summary of Contents for Gold Line Aqua Rite Electronic Chlorine Generator
- Page 1 ® Electronic Chlorine Generator LDLINE CONTROLS INC. www.goldlinecontrols.com 888-921-POOL...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precau- tions should always be followed, including the following: READ AND FOLLOW ALL • INSTRUCTIONS • Disconnect all AC power during installation. • Warning - To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. -
Page 3: Table Of Contents
Troubleshooting Troubleshooting Troubleshooting Warranty Warranty Warranty...15 Warranty Warranty Aqua Rite is a registered trademark of Goldline Controls, Inc ® AquaLink is a registered trademark of Waterpik Technologies, Inc. ® OPERATION OPERATION OPERATION OPERATION OPERATION INSTALLATION INSTALLATION INSTALLATION INSTALLATION INSTALLATION TROUBLESHOOTING... -
Page 4: Operation
OPERATION The Aqua Rite is an automatic chlorine generation system for pool or spa sanita- ® tion. The operation requires a low concentration of salt (sodium chloride) in the pool water. These levels are low enough that it normally will not be tasted. The Aqua Rite automatically sanitizes your pool by converting the salt into free chlorine which kills bacteria and algae in the pool. -
Page 5: Saturation Index
Saturation index The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool water "balance". Your water is properly balanced if the Si is 0 ±.2. If the Si is below -0.2, the water is corrosive and plaster pool walls will be dissolved into the water. -
Page 6: Salt Level
Salt Level Use the chart on page 4 to determine how much salt in pounds or (Kgs) need to be added to reach the recommended levels. Use the equations below (measurements are in feet/gallons and meters/liters) if pool size is unknown. (pool size in feet) Length x Width x Rectangular... -
Page 9: Main Switch
Controls Main Switch Note: When the Aqua Rite RS, the main switch will not funciton. AUTO: For normal operation, the Main Switch should be left in the AUTO position. In this position the Aqua Rite will produce chlorine according to the "Desired Output %"... - Page 10 "Desired Output %" adjustment knob The "Desired Output %" adjustment knob is located in the lower center of the Aqua Rite control panel. This setting is used to control the amount of chlorine the Aqua Rite generates. Raise this setting to increase chlorine level and lower it to decrease chlorine level.
-
Page 11: Spring Start-Up
Maintaining the Aqua Rite System To maintain maximum performance, it is recommended that you open and visually inspect the cell every 3 months or after cleaning your filter. The Aqua Rite will ® remind you to do this by flashing the "Inspect Cell" LED after approximately 500 hours of operation. -
Page 12: Installation
INSTALLATION Installation must be performed in accordance with Local and NEC codes. ELECTRONIC CHLORINE GENERATOR 120/240 VAC POWER LDLINE CONTROLS INC. FROM FROM POOL POOL Preparing Pool/Spa Water Refer to page 1 for recommended chemical levels. The pool's chemistry must be balanced BEFORE activating the Aqua Rite . -
Page 13: Plumbing
Plumbing Ensure that the Aqua Rite the local potable water supply. Consult local plumbing codes. The flow switch and cell should be plumbed in the return line to the pool/spa. The preferred installation is after (downstream) all the pool equipment (filter, heater, solar, etc.). -
Page 14: Wiring
Wiring Power must be shut off at the circuit breaker before performing any wiring. Be sure to follow Local and NEC electrical codes. To provide safe operation, the Aqua Rite must be properly grounded and bonded. Input Power For stand alone operation: Wire the Aqua Rite to the LOAD SIDE of the filter pump timer. - Page 15 Input Power for use with Jandy AquaLink Wire the AquaRite DIRECTLY to 120/240VAC power (not through timer or re- ® lay). AQUALINK RS SUBPANEL NEUTRAL GROUND Optional Jandy AquaLink RS: The Jandy AquaLink RS and Aqua Rite use a 4 wire connection to communicate and can be wired up to 500' apart.
-
Page 16: Troubleshooting
Visit www.goldlinecontrols.com for helpful information on operation, maintenance and troubleshooting your Aqua Rite call for technical assistance at 888-921-POOL. Technicians at the factory are avail- able from 8:00 AM to 8:00 PM Eastern Standard Time, Monday through Friday. Be sure to have the following information when you call: 1. - Page 17 "Low Salt" LED illuminated or flashing Check salt level in pool/spa. If salt level is low, add salt according to chart on page Before adding large quantities of salt, it is advisable to have your salt level professionally checked. "High Salt" LED illuminated Check salt level in pool/spa.
- Page 18 Aqua Rite & Aqua Trol ® This warranty statement is applicable to all Aqua Rite and Aqua Trol units with product date codes of January 1, 2002 and after, and supersedes all warranty statements dated prior to January 1, 2002. This Limited Warranty applies only to Aqua Rite and Aqua Trol Electronic Chlorine Generators.
- Page 19 Problems resulting from installing less than one Aqua Rite unit per 40,000 gallons (25,000 gallons commercial/public pools) or one Aqua Trol unit per 18,000 gallons of pool water. Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alterations, fire, flood, lightning, freezing, external water, war, or acts of God.
- Page 20 ELECTROLYTIC CHLORINE GENERATOR BASIC POOL MAINTENANCE REQUIREMENTS TEST Free Chlorine Alkalinity Salt Stabilizer Calcium Electrolytic Cell inspect & clean www.goldlinecontrols.com Refer to revisions, additional information and helpful service. Or, you may visit your local Authorized Aqua Rite Dealer or call 888-921- LDLINE CONTROLS INC.
Need help?
Do you have a question about the Aqua Rite Electronic Chlorine Generator and is the answer not in the manual?
Questions and answers
how to reset or recalibrate the salt level reading