Advertisement
Commissioning
• Adjust the cable so it does not get snagged.
• Secure the product to the mounting bracket by locating
the screws through the "L" shaped slots (3) in the ceiling
cover and tightening the screws.
• Replace fuse or circuit breaker and switch on. Your light
is now ready for use.
Fitting/replacing bulbs
• When changing a bulb, always switch off at the mains
and allow the bulb to cool before handling. Dispose of
used bulbs carefully. Do not exceed the wattage stated
or use a different shape bulb from that indicated on the
fitting.
• Use a soft cloth to handle bulbs, avoid directly touching
the bulbs as this will shorten their life.
• Remove bulb by turning a quarter turn anticlockwise and
pulling out.
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could
damage the finish.
Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Safety information
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
www.saxbylighting.com
• Push the bulb gently into the lampholder and twist a
quarter turn clockwise to engage pins.
50W GU10
Mains Halogen
Glass parts – Wipe clean with a damp cloth. Do not use
abrasive materials as these will damage the finish.
Iss.2 25092015
Saxby Lighting Ltd. LS9 0SE
Instruction leaflet
Grove Four Light Spotlight
EL-10047
Advertisement
Table of Contents
Related Manuals for Saxby Lighting EL-10047
Summary of Contents for Saxby Lighting EL-10047
- Page 1 Instruction leaflet Commissioning • Adjust the cable so it does not get snagged. • Secure the product to the mounting bracket by locating Grove Four Light Spotlight the screws through the “L” shaped slots (3) in the ceiling cover and tightening the screws. • Replace fuse or circuit breaker and switch on. Your light EL-10047 is now ready for use. Fitting/replacing bulbs • When changing a bulb, always switch off at the mains • Push the bulb gently into the lampholder and twist a and allow the bulb to cool before handling. Dispose of quarter turn clockwise to engage pins. used bulbs carefully. Do not exceed the wattage stated 50W GU10 or use a different shape bulb from that indicated on the Mains Halogen fitting. • Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life. • Remove bulb by turning a quarter turn anticlockwise and pulling out. We recommend cleaning with a soft dry cloth. Glass parts – Wipe clean with a damp cloth. Do not use Do not use solvents or abrasive cleaners as these could abrasive materials as these will damage the finish.
- Page 2 Installation Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference. Existing fittings must be completely removed before installation of a new product. Before removing the existing Warning fitting, carefully note the position of each set of wires. This is a Class 1 product and must be earthed. Always use the correct type and wattage bulb. Exceeding • Undo the screws (1) holding the fixing bracket in place the bulb wattage will damage the product. and set aside. Please read these instructions carefully before commencing any work. When changing a bulb, always switch off at the mains and • Hold the bracket (2) in place and mark the position of allow the old bulb to cool down before handling. Dispose the holes. Ensure that the product is level. This unit must be fitted by a competent and qualified of used bulbs carefully and responsibly. electrician. • Ensure the ceiling is capable of holding the weight of This product is suitable for dimming when used in the product. Take care to avoid damaging any concealed...
Need help?
Do you have a question about the EL-10047 and is the answer not in the manual?
Questions and answers