Page 1
OWNER’S MANUAL Safety, Assembly, Operating, and Maintenance Instructions and ILLUSTRATED PARTS MANUAL PA6685 PERFAERATOR Attachment ™ ™ Please Read and Save These Instructions Effective Date: 02-01-05 For Safety, Read All Safety and Operation P/N 6600-1 Instructions Prior to Operating Machine...
Page 2
Specifications given are based on the latest information available at the time this manual was pro- duced. Walker Mfg. Co. is continually striving to improve the design and performance of its products. We reserve the right to make changes in specifications and design without thereby incurring any obli- gation relative to previously manufactured products.
Walker Manufacturing recommends that any service requiring special training or tools be performed by an authorized Walker Mower Dealer. There are sev- eral general practices to be aware of in the area of safety. Most accidents associated with the oper-...
TIRE/WHEEL SIZE Deck Caster Wheel Roller Wheel * This measurement may vary depending on ground speed PA6685 AERATOR 41-1/2 in. (105 cm) 3.63 x 6 in. (9.22 x 15.25 cm)* 60,000 sq. ft. (5574 sq. meters) Up to 2.50 in. (6.35 cm) 365 lb (136 kg) 23-1/4 in.
If you have any questions concerning setup, op- eration, maintenance, or safety, please contact your authorized Walker Mower Dealer or call Walker Manufacturing Company at (970) 221- 5614. BEFORE OPERATING Read and understand the contents of this OWNER’S MANUAL before operating the...
Replace the machine fuel cap and container cap securely and clean up any spilled fuel before starting the engine. OPERATING NOTE: Refer to the Walker Rider Lawnmowers OWNER’S MANUAL for safety instructions for operating the tractor. Operate the machine only in daylight or in good artificial light with good visibility of areas being aerated.
19. When leaving the machine unattended, disen- gage the PTO clutch, stop the engine, and re- move the ignition key. MAINTENANCE NOTE: Refer to the Walker Rider Lawnmow- ers OWNER’S MANUAL for proper tractor maintenance procedures. To prevent accidental starting of the engine...
The Decal Part Number is listed below and in the Parts Manual; the Decal Location is shown in the Parts Manual. Door Cover (Walker P/N 6682-9) Speed Indicator (Walker P/N 6681-13)
Assembly Instructions SETUP INSTRUCTIONS The PERFAERATOR™ is shipped partially assem- bled. After uncrating, initial setup is required. NOTE: During the process of unpacking, any dam- aged or missing parts should be noted and reported to the delivering carrier immediately (put in writing within 15 days).
Operating Instructions CONTROL IDENTIFICATION, LOCATION, AND FUNCTION CAUTION Before operating the aerator, become fa- miliar with the location and function of all operator controls. Knowing the loca- tion, function, and operation of these controls is important for safe and effi- cient operation of the aerator.
Operating Instructions STARTING THE MACHINE CAUTION ALWAYS disengage the PTO clutch and put the FSC in the NEUTRAL-PARK posi- tion before starting the engine. Refer to the appropriate Tractor Owner’s Manual for tractor starting and operating procedures. ENGAGING THE AERATOR Refer to the appropriate Tractor Owner’s Manual for tractor starting and operating procedures.
Operating Instructions Driving the tractor too fast will make aeration holes appear less frequently and too shallow (short plugs) may do a less than desirable job. Do not engage the PTO with the drive assembly in the transport position. STOPPING THE MACHINE Disengage the PTO clutch.
Camshaft Drive System Lubricate the grease fittings (16) on the camshaft drive system every 4 hours. Use Almagard lubricant (Walker P/N 6685-7). each end and attached to the retractor plate arms are sealed and should be greased every 100 hours of operation.
Maintenance Instructions 1/4 to 1/2 in. (6 to 13 mm) Slack at Midspan Proper Drive Chain Tension Tine Ends Tine ends are adjustable by using the following pro- cedure: Loosen the retaining nut on the tine thread and unscrew tine end to achieve the desired depth. Open side of tine should be to rear.
DU@H Ã LOCATION DU@H LOCATION LOCATION TYPE PLACES The gearbox is permanently lubricated (oil filled) and sealed requiring no scheduled lubrication. However, the gearbox oil seal(s) should be checked every 25 hours for indication of an oil leak. LOCATION TYPE PLACES...
Page 20
DU@H ÃQ6S DESCRIPTION ITEM PART DESCRIPTION S@R·9 REQ’D...
Refer to Body and Frame Components Refer to Control Linkage F013 F290 F076 F318 F149 F383 F013 F123 F051 F051 F041 F005 Refer to Body and Frame Components...
WHAT THIS WARRANTY COVERS, AND FOR HOW LONG: Walker Manufacturing company will, at its option, repair or replace, without charge, any part covered by this warranty which is found to be defective in material and/or workmanship within one (1) year* after date of sale to the original retail pur- chaser unless the product is used for rental purposes, in which case this warranty is limited to ninety (90) days.