Vulcan-Hart ML-114825 Installation And Operation Manual
Vulcan-hart electric tilting skillet operation manual vects16 ml-114825
Hide thumbs
Also See for ML-114825:
- Installation & operation manual (12 pages) ,
- Service manual (24 pages) ,
- Service manual (26 pages)
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vulcan-Hart ML-114825
Summary of Contents for Vulcan-Hart ML-114825
- Page 1 ROUND ELECTRIC TILTING SKILLET MODEL VECTS16 MODEL VECTS16 ML-114825 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 31035 Rev. A (Feb. 2001) INSTALLATION & OPERATION MANUAL www.vulcanhart.com...
-
Page 2: Table Of Contents
Using the Tilting Skillet ... 6 Cleaning ... 7 Cooking Guide ... 8 MAINTENANCE ... 10 Lubrication ... 10 Service and Parts Information ... 10 TROUBLESHOOTING GUIDE ... 11 NOTES ... 12 © VULCAN-HART COMPANY, 1997 TABLE OF CONTENTS – 2 –... -
Page 3: General
Before installing, verify that the electrical service agrees with the specifications on the rating plate located on the right side panel as you face the machine. If the supply and equipment requirements do not agree, do not proceed with the installation. Contact your dealer or Vulcan-Hart Company immediately. -
Page 4: Installation Codes And Standards
INSTALLATION CODES AND STANDARDS The tilting skillet must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. In Canada: 1. -
Page 5: Electrical Data
3. After making the connections, replace the control box cover plate. 4. The tilting skillet must be properly grounded by installing a ground lead to the ground lug located inside the junction box. FLOOR PLAN 29-1/4 (743) 6-3/8 3-7/8 (98) (162) 12-1/2 (318) -
Page 6: Operation
WARNING: THE TILTING SKILLET AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE TILTING SKILLET. CONTROLS Thermostat — Maintains set temperature by controlling power supply. Temperature range is from 100 F to 450 F (38 C to 232 C). Power Switch —... -
Page 7: Cleaning
CLEANING WARNING: BEFORE CLEANING, DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE YOU ARE WORKING ON THE CIRCUIT. Do not use corrosive cleaning agents. After Each Use The tilting skillet should be cleaned after each use. Clean with warm water and a mild detergent. Rinse thoroughly and wipe dry with a soft clean cloth. -
Page 8: Cooking Guide
The guidelines given below are only suggestions for quantities, temperature settings, and estimated numbers of orders per load and per hour. When two temperatures are given, the first is to start the product, the second to complete the product. ITEM BREAKFAST FOODS Bacon Eggs... - Page 9 ITEM MEAT - POULTRY (Continued) Chicken - Pan Fried Chicken - Whole Hot Dogs - Grilled Hot Dogs - Boiled Ham Steak Pork Chops Sausage Links Turkey Off Carcass On Carcass MISCELLANEOUS Grilled Cheese Sandwiches Macaroni & Cheese Rice Spaghetti VEGETABLES Canned Fresh...
-
Page 10: Maintenance
To obtain service and parts information concerning this tilting skillet, contact the Vulcan-Hart Service Agency in your area (refer to listing supplied with the skillet), or Vulcan-Hart Company Service Department at the address or phone number shown on the front cover of this manual. -
Page 11: Troubleshooting Guide
TROUBLESHOOTING GUIDE PROBLEM Skillet will not operate. Hot spot on pan bottom. Skillet difficult to tilt. POSSIBLE CAUSES 1. Power supply not on. 2. Problem with thermostat or heating elements. Contact your local Vulcan-authorized servicer. Problem with heating element. Contact your local Vulcan- authorized servicer. -
Page 12: Notes
— NOTES — – 12 – FORM 31035 Rev. A (Feb. 2001) PRINTED IN U.S.A.
Need help?
Do you have a question about the ML-114825 and is the answer not in the manual?
Questions and answers