Operation - Makita AN613 Instruction Manual

Nose adapter
To prevent the surface of workpiece from being
scratched or damaged, use the nose adapter.
To detach the nose adapter from its housing base, pull
the nose adapter with your thumb in the direction of the
arrow.
► Fig.9: 1. Nose adapter
To attach the nose adapter to the contact element, press
it onto the contact element while the protrusion inside the
nose adapter aligned with the gap in the contact element.
► Fig.10: 1. Contact element 2. Nose adapter
3. Protrusion 4. Gap
Air duster
CAUTION:
Do not aim the ejection port of the
air duster to someone. Also, keep your hands and
foot away from the ejection port. If the air duster
button is accidentally pushed, it may cause a per-
sonal injury.
CAUTION:
Always check your surroundings
before using the air duster. Blown dust or objects
may hit someone.
CAUTION:
Do not connect or disconnect the
air hose while pushing the air duster button.
The air supplied to the tool can also be used as an air
duster. You can clean the work area by pressing the
button on the grip end.
► Fig.11: 1. Air duster button
NOTICE:
After using the air duster, the driving force
of the tool will temporarily decline. Wait until the air
pressure recovers in this case.
NOTICE:
Perform a test blow if you use the air
duster immediately after the oil was applied. The oil
may be sprayed with the air.
ASSEMBLY
CAUTION:
Before carrying out any work on
the tool, always release the trigger and discon-
nect the air hose from the tool.
CAUTION:
Load the same type, size and
uniform length of nails when loading nails in the
magazine.
Loading nailer
CAUTION:
Be careful not to injure yourself
with the fasteners when loading and unloading.
NOTICE:
Select nails suitable for your work.
NOTICE:
Set the coil support plate according to
the nail size to be used. If the tool is operated with
the coil support plate set to the wrong step, poor nail
feed or malfunction of the tool may result.
1. Depress the latch lever and open the door and the
magazine cap.
► Fig.12: 1. Latch lever 2. Door 3. Magazine cap
2.
Lift and turn the coil support plate according to the
nail length to be used.
► Fig.13: 1. Coil support plate 2. Graduation
Nail length
57 mm or 65 mm
45mm or 50mm
38 mm
3. Place the nail coil over the coil support plate.
Uncoil enough nails to reach the feed claw. Place the
first nail in the driver channel and the second nail in the
feed claw. Place other uncoiled nails on feeder body.
Check if the nail coil properly set in the magazine and
then close the magazine cap and the door.
► Fig.14: 1. Feed Claw
Connecting air hose
CAUTION:
Do not rest your finger on the
trigger when connecting the air hose.
► Fig.15: 1. Air fitting 2. Air socket
Slip the air socket of the air hose onto the air fitting on
the tool. Be sure that the air socket locks firmly into
position when installed onto the air fitting.
A hose coupling must be installed on or near the tool in
such a way that the pressure reservoir will discharge at
the time the air supply coupling is disconnected.

OPERATION

CAUTION:
Make sure all safety systems are in
working order before operation.
Checking proper action before
operation
Before operation, always check following points.
— Make sure that the tool does not operate only by
connecting the air hose.
— Make sure that the tool does not operate only by
pulling the trigger.
— Make sure that the tool does not operate only by
placing the contact element against the workpiece
without pulling the trigger.
— In single sequential actuation mode, make sure
that the tool does not operate when pulling the
trigger first and then placing the contact element
against the workpiece.
11 ENGLISH
Position of coil support
plate
Bottom step
Middle step
Top step