VTech CS6129 Quick Start Manual

Quick start guide

for models CS6128-31/CS6129/
CS6129-2/CS6129-3/CS6129-4/
CS6129-31/CS6129-32/CS6129-41/
CS6129-52/CS6129-54
Install the telephone base and
charger(s)
Install the telephone base and charger(s) as
shown below.
Telephone
wall jack
Telephone base
power adapter
DSL filter (not
(large)
included) required
if you have DSL
high-speed
Internet service
Electrical outlet
Telephone line cord
not controlled
by a wall switch
Charger
Telephone base
NOTES:
1. Use only the power adapter(s) and
battery(ies) supplied with your VTech
telephone.
2. For complete feature instructions,
please refer to your user's manual.
Bat te r y inst allation and
charging
Install the battery as shown below. After
installing the battery, you might be able
to make and receive short calls. For best
performance, charge the handset battery for
at least 16 hours before use.
1
2
Plug the battery securely
If the battery
compartment cover is on into the plug inside
the handset battery
the handset, press the
compartment, matching
indentation and slide the
the color-coded label.
cover to remove.
Charger
adapter
(small)
4
3
Place the battery with Align the cover flat
the label THIS SIDE
against the battery
UP facing up and the
compartment, then slide
wires inside the battery
it upwards until it clicks
compartment.
into place.
5
CHARGE light
Charge the handset by
placing it in the telephone
base or charger. The
CHARGE light will be
on when the handset is
charging.
Make, answer and end a call
Make a call
1. Press /FLASH or .
2. Dial the number.
-OR-
1. Dial the number.
/FLASH or
2. Press .
Answer a call
• Press /FLASH, or any of the dialing
keys (0-9, #, * ).
End a call
Press OFF/CLEAR or put the handset in
•
the telephone base or charger.

Activate the answering system

The answering system must be turned on
to answer and record messages. Press
ANS ON/OFF to turn the answering system
on or off. When the answering system is
turned on, it will announce "Calls will be
answered," and the ANS ON/OFF light will be
on. When the answering system is turned off,
it will announce "Calls will not be answered,"
and the ANS ON/OFF light will be off.

Outgoing announcement

The telephone is preset with a greeting that
answers calls with "Hello, please leave a
message after the tone." You can use this
preset announcement, or replace it with
your own.
To record your own announcement:
1. Press ANNC while the telephone is not
in use and the system will announce
"Announcement. Press PLAY or press
RECORD."
2. Pr e s s R E C O R D a n d t h e s y s t e m
announces, "Record after the tone. Press
STOP when you are done."
3. Af ter the tone, speak towards the
microphone at the bot tom front of
the telephone base from about nine
inches away.
4. Press /PLAY/STOP when finished.
5. The answering system will automatically
play the newly recorded announcement.
Press /PLAY/STOP to stop the playback
at anytime.
To play messages:
/PLAY/STOP to play messages
• Press
and stop playback.
• Press X/DELETE while a message is
playing to delete it.
/ S K I P to s k i p to t he nex t
• Pres s
message.
• Press /REPEAT to repeat the current
message.
• Press VOL / to raise or lower playback
volume.
IMPORTANT!
If your product is not working properly:
• Refer to the Troubleshooting section of
the user's manual.
• Visit our website at www.vtechphones.
com or call 1 (800) 595-9511. In Canada,
go to www.vtechcanada.com or dial
1 (800) 267-7377.
96-006860-030-100