Canon Super G3 3rd Line FAX Board-AE1 Service Manual page 19

4
Error Code > Service Error Code
User Error Code
No. T/R
#001 T an original has jammed.
#003 T/R time-out for copying or sending/receiving a single page has occurred.
#005 T/R time-out for initial identification (T0/T1) has occurred.
#008 R a mismatch of passwords at time of polling transmission has occurred.
#009 R recording paper has jammed or is absent.
#012 T recording paper is absent at the other party.
#018 T/R auto call initiation has failed.
#022 T call initiation has failed.
#037 R image memory overflow at time of reception has occurred.
#080 T the other party has no F code reception function/or is not set to receive it.
#081 T the other party has no password reception function/or is not to receive it.
#099 T/R the Stop key is pressed while a communication is under way.
#102 T/R a mismatch of F-code/password has occurred.
#995 T/R a memory communication reservation has been cancelled.
4 Error Code > Service Error Code
Description
Service Error Code
No. T/R
##100 T at time of transmission, the procedural signal has been transmitted more than
specified.
##101 T/R the modem speed does not match that of the other party.
##102 T at time of transmission, fall-back cannot be used.
##103 R at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).
##104 T at time of transmission, RTN or PIN is received.
##106 R at time of reception, the procedural signal is received for 6 sec while in wait for the
signal.
##107 R at time of reception, the transmitting party cannot use fall-back.
##109 T at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received,
and the procedural signal has been sent more than specified.
##111 T/R memory error has occurred.
##114 R at time of reception, RTN is transmitted.
##200 R at time of reception, no image carrier is detected for 5 sec.
##201 T/R DCN is received outside the normal parity procedure.
T-4-1
##204 T DTC without transmission data is received.
##220 T/R system error (main program out of control) has occurred.
##223 T/R while a communication is under way, the line is cut.
##224 T/R in G3 communication, an error has occurred in the procedural signal.
##226 T/R the stack printer has fallen outside the RAM area.
##229 R the recording unit has remained locked for 1 min.
##232 T encoding error has occurred.
##237 R decoding error has occurred.
##238 R the print control unit is out of order.
##261 T/R system error has occurred.
##280 T at time of transmission, the procedural signal has been transmitted more than
specified.
##281 T at time of transmission, the procedural signal has been transmitted more than
specified.
##282 T at time of transmission, the procedural signal has been transmitted more than
specified.
##283 T at time of transmission, the procedural signal has been transmitted more than
specified.
##284 T at time of transmission, DCN is received after transmission of TCF.
##285 T at time of transmission, DCN is received after transmission of EOP.
##286 T at time of transmission, DCN is received after transmission of EOM.
##287 T at time of transmission DCN is received after transmission of MPS.
##288 T after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
##289 T after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
##290 T after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
4-3
Description
4-3