Advertisement
OWNER'S MANUAL & WARRANTY INFORMATION
12 VOLT 2/4/6 AMPERE CHARGE RATES WITH
• IMPORTANT SAFETY INSTRUCTIONS •
WARNING – RISK OF EXPLOSIVE GASES
WARNING - RISK OF EXPLOSIVE GASES
1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS
REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR
CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
2. To reduce risk of battery explosion, follow these instructions and those published by the battery manufacturer
and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary markings on
these products and on engine.
GENERAL SAFETY
1. Use this charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low voltage electrical
system other than in a starter-motor application. DO not use this battery charger for dry-cell batteries that are
commonly used with home appliances. These batteries may burst and cause injury to persons and damage to
property.
2. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire,
electric shock, or injury to persons.
3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in
a risk of fire and electric shock.
If extension cord must be used, make sure:
a. Pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
b. Extension cord is properly wired and in good electrical condition; and
c. Wire size is AWG#14 (14 gauge) to 100 feet and AWG#12 for distances over 100 feet.
5. Do not operate charger with damaged cord or plug - take to a qualified service technician for replacement of the
cord or plug immediately.
6. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in anyway; take it to
a qualified service technician.
7. Do not disassemble charger; contact a qualified service technician when service or repair is required. Incorrect
reassembly may result in risk of electric shock or fire.
8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning
off charger controls will not reduce this risk.
9. Do not operate charger in rain or snow or use when wet.
10. Never charge a frozen battery.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This manual contains important safety and operating instructions for battery charger Model VEC1086B
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 954-584-4446 • FAX: 954-584-5556 • TOLL-FREE 866-584-5504
SMART AUTOMATIC
BATTERY CHARGER
SAVE THESE INSTRUCTIONS:
VEC1086B
Advertisement
Table of Contents
Related Manuals for Vector VEC1086B
Summary of Contents for Vector VEC1086B
-
Page 1: Important Safety Instructions
(2) this device must accept any interference received, including interference that may cause undesired operation. This manual contains important safety and operating instructions for battery charger Model VEC1086B 4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 954-584-4446 • FAX: 954-584-5556 • TOLL-FREE 866-584-5504... - Page 2 PERSONAL PRECAUTIONS AND SAFETY 1. Another person should be close enough to come to your aid when you work near a lead-acid battery. 2. Fresh water and soap should be nearby in case battery acid contacts skin, clothing, or eyes. 3.
- Page 3 FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. A SPARK NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY: Position AC and DC cords/cables to reduce risk of damage by hood, door, or other moving engine parts. 2.
-
Page 4: Introduction And Features
INTRODUCTION AND FEATURES Thank you for selecting the Vector Model VEC1086B 2/4/6 AMP 12 Volt Smart Battery Charger. With proper care and use, it will give you years of dependable service. This battery charger has a high charge rate of up to 6 amps, and low charge rate of up to 2 amps. -
Page 5: Controls And Indicators
FIGURE 3 FRONT VIEW WARNINGS: THERE ARE NO USER-SERVICEABLE PARTS IN THIS CHARGER. DO NOT OPEN THE UNIT! IT MUST BE RETURNED TO VECTOR FOR PROFESSIONAL TESTING AND REPAIR. OPENING THE UNIT WILL VOID THE MANUFACTURER'S WARRANTY. Contact the Vector Technical Support Department at (954) 584-4446 or toll free: (866) 584-5504 for further information. FIGURE 3 FRONT PANEL CONTROLS AND INDICATORS FUNCTIONS... -
Page 6: Charge Rate Selection
• Automatic float can only be achieved after charging is complete and circuit has not been interrupted. GENERAL BATTERY SAFETY With minimal maintenance, the VEC1086B 2/4/6 AMP Smart Battery Charger will provide years of dependable service. Follow these simple steps to maintain the charger in optimum condition: •... -
Page 7: Charging Times
CHARGING TIMES The VEC1086B, a fully automatic Smart Battery Charger will automatically adjust the charge rate as the battery becomes charged and stops charging when the battery is fully charged. For estimates of the time it takes to charge a battery refer to the following table for details. -
Page 8: Warranty
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Manufacturing. Enter “VEC1086B” as Model and “12V 2/4/6 Amp Battery Charger” as Product Type. All Vector Manufacturing, Ltd. products must be registered within 30 days of purchase to activate this warranty. Mail the completed registration form, along with a copy of the original sales receipt to: ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.
Need help?
Do you have a question about the VEC1086B and is the answer not in the manual?
Questions and answers