Related Manuals for Vita-Mix 100 VAC
Summary of Contents for Vita-Mix 100 VAC
- Page 1 I N T E R N A T I O N A L F O O D S E R V I C E Owner’s Manual Read And Save These Instructions Touch and Go Blending Station ® High Performance Commercial Blender 220/240 and 100 VAC Models...
-
Page 2: Important Safeguards
For information on a local distributor call Vita-Mix Service at + 1 ( 440 ) 235-5494. For Latin America call + 1 ( 440 ) 235-0214. 7. The use of attachments not recommended or sold by Vita-Mix Corporation may cause fire, shock, or injury. -
Page 3: Control Panel
See page 6 for information on Custom Programming these six buttons. Display Window DISPLAY WINDOW - This area depending on what button is pressed, OWNER CONTROLS - A control panel accessible by pressing the Vita-Mix logo. M O D E TEMP... -
Page 4: C Ustom Programming
® advanced electronic control can be custom programmed, requiring an optional programming chip, available from Vita-Mix for a nominal fee and with a minimum unit purchase. Contact your Vita-Mix representative for more information . Programming your Touch and Go Blending Station PRE-SET buttons 1. -
Page 5: Electrical Requirements
See page 10 for instructions. Electrical requirements: • Volts: 220/240 VAC • 50 or 60 Hz. • 1073-1178 Watts • Volts: 100 VAC, 60 Hz., 900 Watts (Japan) Blending Station dimensions: • 44.45 cm high with lid closed •... -
Page 6: B Lending Tips
n-Counter Gasket Gasket Installation Instructions: 1. Follow the instructions on page 8 on preparing the counter area for the installation of your In-Counter Touch and Go Also, use the Template Sheet (provided in your machine’s original package) to assist you in the placement and ventilation of your machine. 2. - Page 7 id Assembly Two-part Lid 1.5 Liter Polycarbonate container The two part lid is easy to clean and easy to put on, take off and seal. • To remove fully latched lid, squeeze tabs together on both sides of the container, pull upward and off.
- Page 8 nstructions How to operate your Blending Station six Pre-Set Programmed buttons. The following is the basic factory settings of the six PRE-SET buttons (your machines PRE-SET buttons may be different if your Blending Station was programmed specifically for your business). •...
-
Page 9: B Lade Agitator Assembly
See page 23 “Cooling the motor” for complete instructions. When overheating occurs, review your techniques and instructions. The motor may be getting hot when your recipes are too thick. Consider adding more liquid or consult Vita-Mix for further assistance. lade Agitator Assembly buttons Never use a blade assembly with loose, damaged or knicked components. -
Page 10: Parts List
arts List Item# Part #752 2 liter - Container without lid assembly or blade assembly #755 2 liter - Lid plug #756 2 liter - Container, blade assembly & lid assembly #1191 2 liter - 2-piece lid assembly #1192 2 liter - Lid only (no plug) PLS145 2 liter - 1-piece non-latching rubber lid #1159... -
Page 11: Care And Cleaning
*NOTE: Polycarbonate container, cover and thermoplastic rubber lid are dishwasher safe. However, to prolong the life of these parts, Vita-Mix recommends using a low pH balance soap. For maximum container life, do not use standard dishwasher soaps which contain a high pH balance. -
Page 12: Troubleshooting
• When the motor is cool “READY” will appear in the display window. If you cannot fix your machine with these suggestions, contact your dealer or contact Vita-Mix International at +1(440) 235-5494 for a local distributor, for Latin America call +1(440) 235-0214, or visit us at www.vitamix.com... -
Page 13: Specifications
8615 Usher Road, Cleveland, Ohio 44138-2103 USA ©2001 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system without the written permission of the Vita-Mix Corporation.