Page 1
This user’s guide applies to the following telephone models (when used on Comdial Gxxxx common equipment with lxxxx or Sxxxx software cartridge Rev. 11A and later): 7714S” Rev. I and later 7714X-” Rev. I and later If you need more information,...
GCA 70-221, (your system attendant or whoever runs your main telephone system should have several copies). Typical DigiTech Telephqne (Model 7714s shown) Hold Button ’ ’ Microphone Openln~‘~...
Understanding the Lights on Your Telephone Steady Line is idle Next to A Line Button Next to A Direct Station Station Select (DSS)/ idle Busy Lamp Field (BLF) Button Next to A Fixed Feature or Programmable feature Feature Button is off Your intercom Above the...
Page 4
Uwersranamg steady Above the HOLD BUttOtt Above the MUTE Mute is Button deactivated Steady Red Wlth Telephone On Hook and Busy Above the Speakerphone SPEAKER Button ..^.” _.._.. me Lignts on Your Telephone steady Steady Flashing Flashing Green Orange Massage waiting has been sat Called...
GCA70-280 Using the Speakerphone If your telephone speakerphone handset can be used by pressing instead of lifting the handset. speaker to receive a SOHVA or to originate Answering Calls To answer a call that is ringing at your telephone, if the light is flashing orange, lift handset; if the light is red, press the flashing line and lift handset.
Guide DigiTech Station User’s To respond verbally, Press and hold MUTE, speak into handset. To respond non-verbally, press pre-programmed instructions on programming this function). NOTE: Announcing stafon must have LCD speakerphone. . To Block SOHVA, NOTE: You may block SOHVA only if your telephone is programmed for you to do so.
GCA70-280 To access outside press ITCM, then dial line group access code: 9=groupl, 81 = group 2, 82 = group 3, 82 = group 4, listen for outside dial tone, dial number, when called party answers, lift handset,. To queue for a line group if ail lines are busy, press ITCM and dial line group access code (9,81,82, hear busy tone and dial $8, hang up and wait for queuing ring-back.
Page 8
DigiTech Station User’s Guide To place a call on hold at another telephone, i . while on line, press ITCM (system places call on hold), dial * 90, than dial extension number of telephone to receive held call, hang up handset. To answer a call at the extension lifthandset, press ITCM and dial # 90.
GCA7C-280 Transferring Outside Calls To announce answer outside call, press TFIANSKONF dial station number, upon answer, announce the call, hang up the handset (call is transferred). To transfer a call without answer outside call, press TRANSKONF dial station number, hang up handset. Call will re-ring your telephone if it is not answered within a preprogrammed If you hear a busy signal or receive no answer, press TFtANSKONF and return to outside call.
DigiTech Station User’s Guide Using the Messaging Feature can set system-supplied messages to be displayed at the caking LCD NOTE: speakerphone. To turn LCD messaging press dial +#02, choose MSG, press To retrieve a message, observe flashing message-waiting light, lift handset, press automatic.
GCA70-280 Making a Paging Announcement To page through system provides lit handset, press paging line select button and dial page access code (see your attendant for code) -- if paging is connected to a dedicated paging port, dial ITCY 69, make announcement.
DigiTech Station User’s Guide To forward press ITCM and dial +K 5, dial extension number of station to which calls are to be forwarded. To cancel allcall forward, press ITCM and dial t 5. NOTE: For each personal call received during call forward, you will hear a ring reminder (short tone burst) to remind you that calls are being forwarded.
Engaging Automatic Set Relocation NOTE: If this feature has been enabled by your system programmer, the mes- sage-waiting light will flash for several seconds when you corinect your telephone to another location. This means that the system Is waiting to automatically relocate your extension number and other programmed features to the new location.
Page 14
DigiTech Station User’s Guide To store personal press ITCM and dial * 4 2, dial memory location (l-0). press line button, or dial 1,2,3, or 4 to select line groups i- 4, or dial 0 for system to select line, dial number to be stored (16 digits max.) hookfiash and press HOLD to store pause (if needed), press TRANYCONF, dial next location, select line, and dial another...
Page 16
This manual has been developed by Com- dial Corporation (the ‘Company’) intended for the use of its customers and service personnel. The information in this manual is subject to change without notice. While every effort has been made to elimi- nate errors, the Company disclaims liability for any difftculties arising from the interpre- tation of the information contained herein.