Verilink 41TDM Configuration Manual

Specifications

Network Interface
Service Type: DDS-I or DDS-II clear
channel
Operating Modes: Full duplex, point-to-point,
multi-point
Line Rate: 56 and 72 kbps
Loop Range: Up to 45 dB of loss
Line Connection: RJ-48C jack, 8-pin
modular
Timing Source: DDS-I: Network, Internal
DDS-II: Network
Antistream Timer: Off, 10, 30, or 60 seconds
Supervisory Port
Connection: 8-pin modular (RS-232)
Data Rates: 1.2, 2.4, 9.6, and 19.2 kbps
SLIP Port
Connection: 8-pin modular (RS-232)
Data Rates: 1.2, 2.4, 9.6, and 19.2 kbps
Ethernet (option)
Connection: 8-pin modular
Network Protocol: TCP/ IP-based networks
Data Rate: 10 Mbps
Compatibility: 10BASE-T, ISO/IEC
8802-3
Token Ring (option)
Connection: 8-pin modular (RJ-45)
Network Protocol: TCP/ IP based networks
Data Rate: 4 or 16 Mbps
Compatibility: Type 3 UTP, ISO/IEC
8802-5
Dial Backup
Connection: 6-pin modular
Backup Service: ISDN, sync
Configuration: Information for backup
unit is stored in unit and
transmitted to backup unit
by inband AT commands.
Dialing: Numbers programmed and
stored in unit and
transmitted to backup unit
by inband AT commands.
Restoral: Manual or automatic restoral
to leased line service
Diagnostics
Loopbacks: V.54 (send and receive),
alternating loop (DDS-I),
latching loop (DDS-II)
BERT: 511 pattern
Alarms
Activation: Programmable thresholds
41TDM

Configuration Guide

®
T R A N S P O R T
EXIT SCROLL SELECT
TDM TEST ALARM POWER
PRISM 41TDM
Reporting:
Power
115 VAC:
Mechanical
Housing:
Mounting:
Dimensions:
Weight:
Environmental
Storage Temp:
Operating Temp:
Humidity:
Compatibility
TR 62310:
TR 62310A:
TR 41450:
Internet Standards: RFC 1157 (SNMP)
DDS-I Port Data Rates
Standard mode
Port A:
Port B:
Proprietary, non-TDM mode
Port A:
Port B:
Proprietary, TDM mode
Port A:
Port B:
*
Only one port can be set for 31.2 kbps at a
time. If Port A is set to 31.2 kbps, Port B is lim-
ited to 19.2 kbps. If Port B is set it 31.2 kbps,
Port A is limited to 19.2 kbps.
115VAC
50/60Hz
116ma
LAN SLIP SUPV
DDS-II Port Data Rates
Front panel LEDs, call out
on alarm (COA), SNMP
Standard mode
TRAPs
Port A:
Port B:
116 mA, 8 W max,
27 BTU max
Proprietary, non-TDM mode
Port A:
Plastic standalone case
Desktop or horizontal rack
12 inches (30.40 cm) wide
2 inches (5.08 cm) high
Port B:
9 inches (22.86 cm) deep
Proprietary, TDM mode
4 pounds (1.814 kg)
Port A:
32 to 122 F (0 to 50 C)
4 to 185 F ( 20 to 85 C)
95% maximum (non-
Port B:
condensing)
November 1987
December 1989
*
(addendum 3)
time. If Port A is set to 38.4 kbps, Port B is lim-
November 1981
ited to 19.2 kbps. If Port B is set it 38.4 kbps,
Port A is limited to 19.2 kbps.
RFC 1155 (SMI)
Connections
RFC 1213 (MIB-II)
RFC 1055 (SLIP)
SUPV/SLIP and DDS Pinout
Enterprise TXPORT MIB
Pin SUPV/SLIP
Enterprise DDS MIB
1
2
3
4
Sync onlyat 56 kbps
5
Inactive
6
7
Sync at 2.4, 4.8, 9.6, 19.2,
8
38.4, or 52 kbps
Port A and Port B Pinouts
Async at 2.4, 4.8, 9.6,
ITU Ckt Name
19.2, 38.4, or 57.6 kbps
101/AA Frm Gnd A
Inactive
102/AB Sgnl Gnd B
103/BA
Sync at 2.4, 4.8, 9.6, 19.2,
104/BB
*
or 31.2 kbps
105/CA RTS
Async at 2.4, 4.8, 9.6,
106/CB
*
19.2, or 31.2 kbps
107/CC
108/CD DTR
Sync at 2.4, 4.8, 9.6, 19.2,
*
or 31.2 kbps
109/CF
114/DB TC
Async at 2.4, 4.8, 9.6,
*
115/DD RC
19.2, or 31.2 kbps
141/LLB LL
140/RLB RL
142/TM Test Mode
DBU DDS PORT A
Sync only at 64 kbps
Inactive
Sync at 2.4, 4.8, 9.6, 19.2,
38.4, 56, 60 kbps
Async: at 2.4, 4.8, 9.6,
19.2, 38.4, 56, 57.6 kbps
Inactive
Sync at 2.4, 4.8, 9.6, 19.2,
*
or 38.4 kbps
Async at 2.4, 4.8, 9.6,
19.2, or 38.4
Sync at 2.4, 4.8, 9.6, 19.2,
*
or 38.4 kbps
Async at 2.4, 4.8, 9.6,
19.2, or 38.4
Only one port can be set for 38.4 kbps at a
DDS
DTR Out Data Out (Tip)
RTS Out Data Out (Ring)
Frame Gnd
Data Out
Data In
Signal Gnd
CTS In Data In (Tip)
DCD In Data In (Ring)
V.35 RS-232 EIA-530 DCE
1
7
TxD P, S 2
RxD R, T 3
C 4
CTS D 5
DSR E 6
H 20
DCD F 8
Y, AA 15
V, X 17
18
21
45-00129
4.0
PORT B
*
kbps
*
kbps
1 Gnd
7 Gnd
2, 14 In
3, 16 Out
4, 19 In
5, 13 Out
6, 22 Out
20, 23 In
8, 10 Out
12, 15 Out
9, 17 Out
18 In
21 In
25 Out