Makita DUR190U Instruction Manual page 20

Attaching the barrier
For DUR190L and DUR191L (country specific)
If the barrier is included in your model, attach it to the
handle using the screw on the barrier.
► Fig.14: 1. Barrier 2. Screw
CAUTION:
After assembling the barrier, do
not remove it. The barrier works as a safety part
to prevent you from contacting the cutting blade
accidentally.
Mounting the attachment pipe
For DUR191U and DUR191L only
Mount the attachment pipe to the power unit.
1. Turn the lever to the direction of the arrow shown
in the figure.
► Fig.15: 1. Lever
2. Pull up the joint cover and insert the attachment
pipe while aligning the protrusion on the pipe (cutting
tool side) with the concave portion of the joint part.
► Fig.16: 1. Lock lever 2. Joint cover 3. Pipe
Make sure that the surface of the lock lever is parallel
to the pipe.
3. Turn the lever to the direction of the arrow shown
in the figure.
► Fig.17: 1. Lever
To remove the pipe, turn the lever to the direction of the
arrow shown in the figure and pull the pipe out while
pressing down the lock lever.
► Fig.18: 1. Lever 2. Lock lever 3. Pipe
Installing the protector
WARNING:
Never use the tool without the
guard illustrated in place. Failure to do so can
cause serious personal injury.
CAUTION:
Take care not to injure yourself on
the cutter for cutting the nylon cord.
Attach the protector to the clamp using bolts.
► Fig.19: 1. Clamp 2. Protector 3. Cutter
Installing the cutting tool
NOTE: The type of the cutting tool(s) supplied as
the standard accessory varies depending on the
countries. The cutting tool is not included in some
countries.
NOTE: Turn the tool upside down so that you can
replace the cutting tool easily.
Cutter blade
CAUTION:
When handling a cutter blade,
always wear gloves and put the blade cover on
the blade.
CAUTION:
The cutter blade must be well pol-
ished, and free of cracks or breakage. If the cutter
blade hits a stone during operation, stop the tool and
check the cutter blade immediately.
CAUTION:
Always use the cutter blade
with the diameter described in the section for
specifications.
► Fig.20: 1. Nut 2. Cup 3. Clamp washer 4. Cutter
blade 5. Spindle 6. Guard 7. Spindle lock
button
1. Mount the cutter blade onto the guard so that the
arrows on the cutter blade and protector are pointing in
the same direction.
► Fig.21: 1. Arrow
2. Put the clamp washer and cup onto the cutter
blade.
3.
While holding down the spindle lock button,
tighten the nut securely by the box wrench.
► Fig.22: 1. Spindle lock button 2. Box wrench
3. Loosen 4. Tighten
To remove the cutting blade, loosen the nut while hold-
ing down the spindle lock button.
Nylon cutting head
NOTICE:
Be sure to use genuine Makita nylon
cutting head.
While holding down the spindle lock button, place
the nylon cutting head onto the spindle and tighten it
securely by hand.
► Fig.23: 1. Nylon cutting head 2. Spindle 3. Spindle
lock button 4. Loosen 5. Tighten
To remove the nylon cutting head, loosen the nylon
cutting head while holding down the spindle lock button.
Plastic blade
NOTICE:
Be sure to use genuine Makita plastic
blade.
While holding down the spindle lock button, place the
plastic blade onto the spindle and tighten it securely by
hand.
► Fig.24: 1. Plastic blade 2. Spindle 3. Spindle lock
button 4. Loosen 5. Tighten
To remove the plastic blade, loosen the plastic blade
while holding down the spindle lock button.
NOTE: You can use the supplied hex wrench to
install/remove the cutting tool. Insert the hex wrench
to the hole as shown in the figure to lock the spindle.
► Fig.25: 1. Hex wrench 2. Hole
20 ENGLISH