Related Manuals for IXXAT CANblue
Summary of Contents for IXXAT CANblue
- Page 1 Manual CANblue Intelligent Bluetooth/CAN Interface The experts for industrial and automotive communication...
- Page 2 Internet: www.ixxat.de Internet: www.ixxat.com e-Mail: info@ixxat.de e-Mail: sales@ixxat.com Support In case of unsolvable problems with this product or other IXXAT products please contact IXXAT in written form by: Fax: +49 (0)7 51 / 5 61 46-29 e-Mail: support@ixxat.de Copyright Duplication (copying, printing, microfilm or other forms) and the electronic distribution of this document is only allowed with explicit permission of IXXAT Automation GmbH.
-
Page 3: Table Of Contents
CAN bus termination ..............9 Appendix...................10 Technical specifications............10 FCC Compliance ............... 11 IC Compliance ................11 Notes on EMC ................12 Disposal of waste electronic equipment ......... 12 EC declaration of conformity ..........13 Copyright IXXAT Automation GmbH CANblue- Manual, V1.5... -
Page 5: Introduction
This manual is intended to familiarize you with your interface, also referred to in the following as CANblue. Please read this manual before beginning with the in- stallation. The CANblue is particularly suitable for wireless diagnosis and parameterization of CAN networked applications. -
Page 6: Returning Hardware
In the case of repairs, please also describe the problem or fault in detail on the RMA form. This will enable us to carry out the repair quickly. Copyright IXXAT Automation GmbH CANblue - Manual, V1.5... -
Page 7: Installation
Hardware installation In order to operate the CANblue, a Bluetooth interface is required on the PC in accordance with the Bluetooth specification V 2.0. The device is recognized as a network adapter and activated via a so-called RF-COM port in the PC. -
Page 8: Connections And Displays
Table 3-1: Pin allocation Power 3.1.2 CAN bus connector The CANblue has a bus interface in accordance with ISO 11898-2 and ISO 11898-3. Switch over between the two interfaces can be made via software. The signals of the bus interface are connected to the 9-pin Sub-D connector (see Ta- ble 3-2). -
Page 9: Displays
Table 3-3: LED states CAN bus termination There is no bus termination resistor for the CAN bus fitted on the CANblue. For simple integration of the bus termination resistor in accordance with ISO 11898- 2, IXXAT offers an appropriate feed-through connector with integrated bus ter- mination. -
Page 10: Appendix
88 x 72 x 35 Weight: approx. 156 g Working temperature range 0 – 55 °C Relative humidity 10-95%, non-condensing EMC test in accordance with EN 5022:1998 + A1:2000 EN 5024:1998 Protection type IP 40 Copyright IXXAT Automation GmbH CANblue - Manual, V1.5... -
Page 11: Fcc Compliance
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for Copyright IXXAT Automation GmbH CANblue- Manual, V1.5... -
Page 12: Notes On Emc
IC ID: 5325A-90202L Notes on EMC The PC/CAN interface CANblue may only be installed in a PC with a CE symbol. The CAN bus connected to the interface must have a shielded cable and the braiding is to be connected to the connector housing using the largest possible surface area. -
Page 13: Ec Declaration Of Conformity
Appendix EC declaration of conformity IXXAT Automation declares that the product: CANblue with the article number: 1.01.0125.00000 meets the requirements of the standards: DIN EN 55022/ 05.1999, class B + A1:2000 DIN EN 55024/ 05.1999 according to the following test report: IX337_01.DOC...
Need help?
Do you have a question about the CANblue and is the answer not in the manual?
Questions and answers