Table of Contents
Advertisement
Viewing Migration Status
kickstart variable = bootflash:/n7700-s3-kickstart.8.4.1.bin
system variable = bootflash:/n7700-s3-dk9.8.4.1.bin
Boot POAP Disabled
sup-2
kickstart variable = bootflash:/n7700-s3-kickstart.8.4.1.bin
system variable = bootflash:/n7700-s3-dk9.8.4.1.bin
Boot POAP Disabled
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2019, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
Switch# show module
Mod Ports Module-Type
--- ----- ----------------------------------- ------------------ ----------
1
48
1/10 Gbps Ethernet Module
2
30
10/25/40/100 Gbps Ethernet Module
3
0
Supervisor Module-3
4
0
Supervisor Module-2
5
30
10/25/40/100 Gbps Ethernet Module
6
30
10/25/40/100 Gbps Ethernet Module
Mod
Power-Status
---
-------------
3
powered-dn
After the supervisor 3E module has been moved to Active mode, non-disruptive migration from supervisor 2E modules
to supervisor 3E modules is completed. A console message, SUP3_MIGRATION_COMPLETE, is then displayed.
Viewing Migration Status
Use the show logging onboard migration status command on any management session to display the status
of migration. You can use this command during migration or after migration is complete.
The sample output when this command is used on the supervisor-3E module is as given below. This output
has both the supervisor-3E and the supervisor-2E logs.
switch#
<Sat May 25 01:58:22 2019> ===============================================
<Sat May 25 01:58:22 2019> Starting Supervisor-3 (N77-SUP3E) migration logging
<Sat May 25 01:58:22 2019> ===============================================
<Sat May 25 01:58:22 2019> Migrate file is created
<Sat May 25 01:58:22 2019> Migration in progress, scratchpad register : 0xfe
and boot_type : 1
<Sat May 25 01:58:22 2019> Written 0xed post migration file creation
<Sat May 25 01:58:22 2019> Post write, read scratchpad_b register 0xed
<Sat May 25 02:05:00 2019> Copying the everland migration log from tmp to plog
succeeded
<Sat May 25 02:05:14 2019> bootvar_handle_mts_msg: migration in progress - 1
<Sat May 25 02:05:14 2019>
bootvar_copy_cfg_for_migration:sup_migration_procjob_hdl : 0
<Sat May 25 02:05:14 2019> bootvar_copy_cfg_for_migration:forking procjob for
copy r s
<Sat May 25 02:05:15 2019> Standby arbiter link of F4 card in slot 6 has been
changed to 12G
Cisco Nexus 7710 Switch Site Preparation and Hardware Installation Guide
102
Reason
---------------------
Reset (powered-down) because of incompatible configuration
show logging onboard migration status
Installing or Replacing Modules, Fan Trays, and Power Supplies
Model
Status
N77-F348XP-23
ok
N77-F430CQ-36
ok
N77-SUP3E
active*
N77-SUP2E
powered-dn
N77-F430CQ-36
ok
N77-F430CQ-36
ok
OL-30452-01.
Advertisement
Table of Contents
