Related Manuals for Uniden EXP 2905
Summary of Contents for Uniden EXP 2905
- Page 2 Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Uniden’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources. ®...
- Page 3 Please do not attempt to unplug any appliance during an electrical storm. Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by the instruction manual, could void your authority to operate this product.
- Page 4 Plug the AC Adapter into a standard 120 VAC wall outlet. Do not use an outlet controlled by a wall switch. Use only the Uniden AC Adapter supplied with this phone.
- Page 5 Redialing Storing phone numbers on the handset Storing phone numbers on the base phone Making calls with memory dialing on the handset Making calls with memory dialing on the base phone Turning off the ringer Checking the ringer type Adjusting the ringer volume level of the base phone To switch from the base phone to the handset...
- Page 6 Before you use your phone, you must first set it up. Here's a quick way to set up your phone: Steps 1, 2 and 3. First, unpack the phone and the supplied accessories. The cordless telephone uses a digital security code to provide protection against unwanted access to your base phone.
- Page 7 Make sure you have received the following items in the package. Uniden Parts Department (800) 554-3988 Hours: M-F 7:00 AM to 5:00 PM CST. We can also be reached on the web at www.uniden.com Getting Started...
-
Page 8: Choose The Best Location
Do the following steps: • Choose the best location • Connect the base phone • Choose the dialing mode Where you place the base phone affects the reception quality of the handset. : • Should you experience intermittent loss of audio during a conversation, try moving closer to the base or move base phone away from other noise sources. - Page 9 If you want to hang the base phone on the wall, see page 32. If you want to use the wall bracket as the stand, attach it on the bottom of the base phone before step 1 as illustrated above. ∆...
- Page 10 • Use only the supplied AD-314 AC power adapter. Do not use any other AC power adapter. • Connect the AC power adapter to a continuous power supply. • Place the base phone close to the AC outlet so that you can unplug the AC power adapter easily.
- Page 11 Charge the battery pack for 15-20 hours before you start using your phone. Slide open the battery compartment lid of the handset. Connect the battery connector with correct polarity (black wire goes on left side and red wire goes on right).
- Page 12 If the battery lasts only a few minutes even after the usable life of the battery has expired and needs replacement. Contact Uniden Parts Department (see page 7), and ask for a rechargeable battery pack. Battery life may vary depending on usage condition and ambient temperature.
- Page 13 Refer to the pages indicated in parentheses for details. (p. 16, 20) Lights up during a call, flashes when you store a phone number for memory dialing. Adjusts the handset volume. (p. 16, 19) Lets you make or receive a call. (p.
- Page 14 (p. 21) Used to store numbers for memory dialing. (p. 17) (p. 17, 19) Allows you to switch temporarily to tone dialing. (p. 17, 19, 25) Lights when one of the phones is in use. (p. 11) Lights while the battery is being charged.
- Page 15 18 19 20 21 (p. 17, 19) Adjusts the speaker volume. (p. 28) Used to make an intercom call. (p. 27) Lights up during an intercom call. (p. 24) Adjusts the ringer volume. (p. 10) Selects pulse or tone dialing. (p.
- Page 16 HOLD TONE Put a call on hold Press The TALK/BATT LOW LED flashes slowly. Press Select a better channel Press Adjust the handset Set the VOL switch to H (high), M (middle) or L Volume (low). Switch to tone dialing Press Temporarily you’re connected.
- Page 17 You hear a beep every three seconds and the TALK/BATT LOW LED on the handset flashes. The call will disconnect soon. Replace the handset on the base phone to charge. Note that during the first 10 - 15 minutes of charging, the phone will be inactive, i.e., unable to make or receive a call.
- Page 18 • You may not be able to hear the other party’s voice in a noisy place. Therefore, use the speakerphone in a quiet room. • Do not bring your hand or other object too close to the microphone or you will hear a shrill noise (“feedback”). •...
- Page 19 HOLD TONE Put a call on hold Press The TALK/BATT LOW LED flashes slowly. Press Select a better channel Press Adjust the handset volume Set the VOL switch to H (high), M (middle) or L (low). Switch to tone dialing Press temporarily The line remains in tone dialing until disconnected.
- Page 20 You can dial with a touch of a few buttons by storing a phone number on a dialing key. You can store up to 10 different phone numbers separately on the handset and on the base phone. TALK REDIAL/P MEMORY •...
- Page 21 MEMORY REDIAL/P SPEAKER • In step 3, if you don’t enter the phone number, the previously stored number will be erased. • Do not allow more than 20 seconds to elapse between each step of the procedure. • You cannot store phone numbers on the base phone while the handset is being used.
- Page 22 Press directly after step 2, then go to step 4. REDIAL/P Before entering a phone number in step 3 on the previous page, do as follows: Enter the outside line access digit (e.g. 9). Press REDIAL/P To store a new number, follow the instructions described previously. Press SET UP on the handset/...
- Page 23 You can select a ringer type from four types. TONE Press SET UP Press TONE Press Press The ringer on the handset is turned off. Follow the instructions described in “Setting the ringer type.” Do not allow more than 20 seconds to elapse between each step of the procedure.
- Page 24 Press SET UP Press TONE Press The currently selected ringer sounds. Press If you hear no sound (only key beep), the ringer on the handset has been turned off. Set the RINGER switch on the base phone to HIGH or LOW. To turn the ringer off, set it to OFF.
- Page 25 When you put a call on hold, you can return to the call on the other phone without disconnecting the call. TALK • If you pick up the handset while talking through the speakerphone on the base phone, the call will be switched to the handset. HOLD •...
- Page 26 Press on the handset. HOLD The TALK/BATT LOW LED and the LINE LED on the base phone will flash slowly. Press SPEAKER The SPEAKER LED on the base phone will light up. The TALK/BATT LOW LED will flash. When you are done talking, press again.
- Page 27 You can talk between the base phone and the handset. You can start the intercom from either phone. TALK • You can receive an intercom call on the base phone even when the RINGER switch on the base phone is set to OFF. The base phone will ring at a low level.
- Page 28 SPEAKER • If there is an incoming call while on the intercom, only the base phone rings at a low level. To answer the call, press on the base phone. The intercom is canceled and you can SPEAKER talk to the outside caller. •...
- Page 29 You can transfer a call between the handset and base phone without disconnecting the call. SPEAKER TALK You can receive an intercom call on the handset even when the ringer is set to off. The handset will ring at a high level. Press INTERCOM The call is put on hold, the...
- Page 30 TALK INTERCOM SPEAKER • You can receive an intercom call on the base phone even when the RINGER switch on the base phone is set to OFF. The base phone will ring at a low level. • When a person at the base phone want to answer the intercom call within 3 seconds, press INTERCOM press...
- Page 31 The handset and the base phone operate like two extensions on the same line. Both phones can operate at the same time, so that you, the outside caller, and the person at the other phone can engage in a three-way conversation.
- Page 32 To remove the wall bracket, press the lower tabs. Additional Information Raise the hang-up tab. Plug the telephone line cord to the LINE jack and the AC power adapter to the DC IN 9V jack, and hook the cords. Attach the wall bracket to the center of the base phone.
- Page 33 If you’ve experienced any of the following difficulties while using your phone, use this troubleshooting guide to help you remedy the problem. Should any problem persist, call our customer hotline at 1-800-297-1023. You hear five short error beeps when you press TALK You hear no dial tone.
- Page 34 You cannot store a memory dialing number. You cannot make a memory dialing call. Memory dialing is incorrect. The handset does not ring when calling from the base phone. The CHARGE LED does not light up when you place the handset to charge.
- Page 35 Frequency band 902 - 928 MHz Operating channel 40 channels Dial signal Tone, 10 PPS (pulse) selectable Supplied accessories See page 7. Power source Rechargeable battery pack BT-905 Battery charging time Approx. 15-20 hours Battery life Standby: Approx. 7 days Talk: Approx.
- Page 36 Adjusting volume handset volume 16 speaker volume 17, 19 Battery pack charging 11 duration 12 Connection 9 Dialing mode choosing 10 switching to the tone temporarily 16, 17, 19 Identifying the parts 13 Intercom 27 Location, base phone 8 Additional Information Making calls 16 Memory dialing 20 Mounting the base phone...
- Page 39 WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale.