Owlet Home J1 Quick Start Manual
Smart video doorbell
Hide thumbs
Also See for J1:
- Quick start manual (11 pages) ,
- Quick start manual (4 pages) ,
- Quick start manual (11 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Owlet Home J1
Summary of Contents for Owlet Home J1
-
Page 2: What's In The Box
1. what’s in the box Please consult below checklist for all the components. Video Doorbell USB Cable User Guide Indoor Chime Screw & Tools Adhesive Tape 2. meet the doorbell 2MP camera LED indicator Security screw hole Micro-SD card slot Motion sensor Charging indicator Microphone... -
Page 3: Battery Installation
4. Battery installation isolating film The batteries are pre-installed in the doorbell, with an isolating film inserted in the positive poles. Please remove the film and insert the battery pack back to compartment, with positive poles upwards! NOTE: Improper battery installation will cause damage to the internal components and may result in serious injury. -
Page 4: Run A Test
Guiding steps: 9:55 9:55 9:55 9:55 Install Doorbell Install Doorbell Devices Install Doorbell Camera Doorbell Battery Camera Floodlight Camera Press the [Bell] button, and tap Next Please reset the device Please follow the instruction manual to power the device Help Using the supplied reset pin, reset the device(please consult the user manual for more on Please stay near your router for the best signal... -
Page 5: Live Viewing
9. Live viewing Wi-Fi signal status Quit live viewing Screenshot button Setting menu Speak to the scene Battery status Volume on/off Record on the phone HD/SD switch Body detection on/off Full screen display Notification history Stream bit rate Cloud storage service Note: Live viewing will not trigger device recording. - Page 6 11. leave Voice messages Maximum 3 voice messages (Max. 10 seconds each) can be pre-recorded into the doorbell, which enables you to quickly respond to your visitors when you are not convenient to answer the doorbell call. Setting --> Basic function -->...
- Page 7 Sharing by QR code scanning The new users can show their QR codes to the administrator, and share device by QR Code scanning. CloudEdge App >> Tap on “ ” >> “User Name” >> “My QR Code” Find your QR code: >>...
-
Page 8: Select Ringtone
Pair with doorbell Tap on “ ” and enter into Settings-> Basic function -> Wireless Chime .(refer to Picture.4) Wireless Chime Settings BasicFunction Night Vision Chime Reminder Automatic Host Leaves Message Wireless Chime Receive Notifications Power Management Device Share Picture.5 Ring Volume Device Information Middle... -
Page 9: Installation
14. Installation 166° Select location Your doorbell has 166-degree view angle and 120-degree human detection range. 5 feet 160cm It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance. - Page 10 Go wireless installation The Smiths (Example) 1. Dismount the bracket by pushing from 2. Bracket installation: mount the bracket on 3. (Optional) The nameplate holder can be the back of your doorbell. Please remove the wall with screws & anchors or the double mounted on the top rear/ bottom rear of the the insulation film in the battery cell.
-
Page 11: Specification
15. Specification Video doorbell Indoor Chime Video & Audio General Image Sensor 1/2.7” CMOS (2.0MP) Power source DC 5V 1A Lite-OS Power port USB (Type-A) 1920 × 1080 px Resolution Consumption 0.2W HD/SD dual stream Stream Ringtones 4 ringtongs optional Infrared LED High power IR LED with ICR Volume... -
Page 12: Troubleshooting
16. Trouble shooting Q1: Why I failed to set up Wi-Fi for the doorbell? .Device works with 2.4GHz Wi-Fi only, but not support 5GHz Wi-Fi. .Wi-Fi network is not good, try to keep the camera near the Wi-Fi router when setting up. .The Wi-Fi password is wrong.
Need help?
Do you have a question about the J1 and is the answer not in the manual?
Questions and answers