Panasonic SB-HS950P Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Speaker System
  5. SB-HS950P
  6. Service manual
Panasonic SB-HS950P Service Manual

Panasonic SB-HS950P Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Specification
Type
Speaker unit(s)
Full range
Input power (IEC)
Output sound pressure
Frequency range
Dimensions (W x H x D)
CONTENTS
1 way, 1 speaker system (Bass reflex)
Impedance 4 Ω
6.5 cm (2-1/2") cone type
100 W* (Max)
80 dB/W (1.0 m)
89 Hz - 25 kHz (-16 dB)
105 Hz - 22 kHz (-10 dB)
92 x 142 x 95 mm
SB-HS950P
Colour
(K)... Black Type
Mass
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
* : Rating with low-cut filter equipped amplifier.
Page
2
2
2
3
3
4
5
© 2007 Matsushita Electric Industrial Co. Ltd.. All
rights
distribution is a violation of law.
ORDER NO. MD0702011CE
Speaker System
(3-5/8" x 5-19/32" x 3-3/4")
0.6 kg (1.32 lbs)
reserved.
Unauthorized
copying
A6
Page
5
6
9
10
10
11
and

Advertisement

Table of Contents
loading

Related Manuals for Panasonic SB-HS950P

Summary of Contents for Panasonic SB-HS950P

  • Page 1: Table Of Contents

    ORDER NO. MD0702011CE Speaker System SB-HS950P Colour (K)... Black Type Specification Type 1 way, 1 speaker system (Bass reflex) (3-5/8” x 5-19/32” x 3-3/4”) Impedance 4 Ω Speaker unit(s) Mass 0.6 kg (1.32 lbs) Full range 6.5 cm (2-1/2”) cone type...

  • Page 2: System Combination

    The diagrams below show the breakdown for speaker combinations used in main unit systems. SB-PT950P-K consists of SB-HF950P-K (x2), SB-HS950P-K (x2), SB-HC950P-K (x1) 1.2. Packaging information Note : Please refer to service manual of SB-HF950P-K (MD0702010CE) to understand the packaging condition for SB-HS950P-K.

  • Page 3: Assembling And Disassembling

    SB-HS950P 2 Assembling and Disassembling “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
  • Page 4 SB-HS950P 2.2. Disassembly of Rear cabinet shown. Caution: Do not exert strong force as it may damage the rear cabinet. Step 1: Remove 4 screws. Step 5: Detach the blue (+) and gray (-) wires. Step 2: Upset the speaker unit as shown above.
  • Page 5 SB-HS950P 2.3. Disassembly of Woofer 2.4. Disassembly of Terminal jack Follow (step 1) to (step 4) in item 2.2. Follow (step 1) to (step 5) in item 2.2. Step 1: Remove 1 screw from the terminal jack. Step 1: Detach the gray (-) and blue (+) wires.

  • Page 6: Connection Of The Speaker Cables

    SB-HS950P 3 Connection of the Speaker Cables · Be sure to connect speaker cables before connecting the AC power supply cord. · The load impedance of any speaker used with this unit must be 4 Ω. · Be sure to connect the cable from the right speaker to the right terminal and the cable from the left speaker to the left terminal.
  • Page 7 SB-HS950P Positioning the speakers...
  • Page 8 SB-HS950P Note on speaker use · Use only supplied speakers. Using other speakers can damage the unit, and sound quality will be negatively affected. · You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods.

  • Page 9: Connection Of The Wiring Diagram

    SB-HS950P 4 Connection of the Wiring Diagram...

  • Page 10: Exploded View

    SB-HS950P 5 Exploded view 5.1. Cabinet Parts Location...

  • Page 11: Replacement Parts List

    SB-HS950P 6 Replacement Parts List Notes : · Important safety notice : When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list. · [M] markings in the Remarks columns indicates parts supplied by PAVCSG.

Table of Contents