Save These Instructions - Troy-Bilt TB55B Operator's Manual

SAFETY WARNINGS FOR CHARGING STANDS
AND LEAD-ACID BATTERIES
• Before using the charging stand, read all instructions
and cautions in this manual, as well as on the charging
stand, and on the unit.
• Do not expose charger to rain or snow.
• To reduce risk of injury, charge only sealed lead-acid
rechargeable batteries. Other types of batteries may
burst, causing personal injury and damage.
• To reduce risk of damage to charger body and cord,
pull it by the charger body (not the cord) when
disconnecting the charger.
• Make sure the charger cord is located in an area where
it will not be stepped on, tripped over or otherwise
subjected to damage or stress.
• Do not operate the charger with a damaged cord or
plug. If damaged, replaced the charger immediately.
• Do not operate charger if it has received a sharp blow,
been dropped or has been damaged in any way. If the
charger case is damaged, replace the charger.
• Do not disassemble the charger. The charger is not
serviceable; disassembly may result in a electric shock
or fire.
• To reduce the risk of electric shock, unplug the charger
from the outlet before you clean or service the unit.
• Do not use the charger outdoors.
• Use only the following type and size battery: 12 volt
DC, sealed lead-acid battery (182391).
• Do not dispose of batteries in fire. The cell may
explode. Batteries should be recycled. Consult your
local waste authority for information regarding available
recycling and/or disposal options.
• Exercise care when handling the batteries. Be careful
and avoid shorting the battery with conducting
materials like rings, bracelets and keys. The battery or
conductor may overheat and cause burns.
• Charge the battery in a location where the temperature
is between 50˚F (10˚C) and 100˚F (38˚C).
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
WHILE OPERATING
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty. Long sleeve shirts
are recommended.
• Wear heavy, long pants, boots and gloves. Do not
wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level.
• The cutting attachment shield must always be in place
while operating the unit. Do not operate unit without
the trimming lines extended, and the proper line
installed. Do not extend the trimming line beyond the
length of the shield.
• Adjust the D-handle to your size to provide the best grip.
4
RULES FOR SAFE OPERATION
• Be sure the cutting attachment is not in contact with
anything before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Do not carry around a unit
with your finger on the trigger switch.
• Use the right tool. Only use this tool for the purpose
intended.
• Do not overreach. Always keep proper footing and
balance.
Always hold the unit with both hands when operating.
Keep a firm grip on both the battery housing grip and
the D-handle.
• Keep hands, face and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it is rotating.
• Do not operate the motor faster than the speed needed
to cut, trim or edge. Do not run the motor at high
speed when you are not cutting.
• Always stop the motor when cutting is delayed or
when walking from one cutting location to another.
• If you strike or become entangled with a foreign object,
stop the motor immediately and check for damage. Do
not operate before repairing damage. Do not operate
the unit with loose or damaged parts.
• Release the trigger, ensure the lock-off button resets
and allow the motor to stop for maintenance or repair.
• Use only original equipment manufacturer replacement
parts when servicing this unit. These parts are available
from your authorized service dealer. Do not use
unauthorized parts, accessories or attachments. Using
unauthorized parts may lead to serious injury, damage
to the unit and a voided warranty.
• Keep the unit clean of vegetation and other materials.
They may become lodged between the cutting
attachment and shield.
OTHER SAFETY WARNINGS
• Disconnect the unit from the power supply when it is idle,
when you are storing or transporting it, when you are
servicing it, and when you are changing attachments.
• Store the unit in a dry area, locked up to prevent
unauthorized use or damage, and stored in a high
place out of the reach of children.
• Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use. See the Cleaning and Storage
instructions.
• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS