Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Troy-Bilt 52067 - 5HP
Summary of Contents for Troy-Bilt 52067 - 5HP
-
Page 1: Parts List
SAFETY FIRST! Before operating this equipment, read this Owner's Manual and the separate manual supplied by the engine manufacturer. Model 52067 - 5HP OWNER’S MANUAL Trimmer/Mower Safety • Assembly • Features and Controls • Operation • Maintenance • Parts List •... -
Page 2: Table Of Contents
Dear Owner: You now own one of the finest trimmer/mowers available. It was designed to easily handle a wide variety of trimming, mowing and clearing chores. You will find the machine to be an invaluable tool in caring for your property. -
Page 3: Section 1: Safety
SPARK ARRESTER WARNING TO RESIDENTS OF CALIFORNIA AND SEVERAL OTHER STATES Under California law, and under the laws of several other states, you are not permitted to operate an inter- nal combustion engine using hydrocarbon fuels on any forest, brush, hay, grain, or grass covered land; or land covered by any flammable agricultural crop with- out an engine spark arrester in continuous effective working order. -
Page 4: Slope Operation
Section 1: Safety 16. Do not operate the machine while under the influence of alcohol or drugs, or when tired or ill. 17. If using machine in wet conditions, exercise extreme care to prevent loss of footing. Wear footwear that will improve traction. -
Page 5: Safety Decals
e) Replace caps on the fuel tank and fuel container and clean up spilled fuel before starting engine. Move machine away from any gasoline fumes before starting the engine. f) Keep matches, smoking materials, open flames, and sparks away from the fuel tank and fuel container. -
Page 6: Section 2: Assembly
WARNING To prevent personal injury or property damage, do not attempt to start the engine until all assembly steps are complete and you have read and under- stand safety the operating instructions in this Manual. INTRODUCTION Carefully follow these assembly steps to correctly prepare your machine for use. - Page 7 Section 2: Assembly Figure 2-3: Attach throttle lever to right-side handlebar. Figure 2-1 Figure 2-4: Check trimmer head hardware for tightness. Figure 2-2: Handlebar installation.
-
Page 8: Section 3: Features And Controls
Section Features and Controls OPERATING SYMBOLS Various symbols (shown here, with word descriptions) are used on the unit. WARNING Before operating your machine, care- fully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. -
Page 9: Section 4: Operation
WARNING Before operating your machine, care- fully read and understand all safety (Section 1), controls (Section 3) and op- erating instructions (Section 4) in this Manual, in the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. -
Page 10: Use Correct Diameter Trimmer Line
Section 4: Operation USE CORRECT DIAMETER TRIMMER LINE For tougher cutting conditions, use two (or four) sections of the thicker, .155" di- ameter extra-heavy duty line. For less demanding conditions, use two sections of the thinner, .130" diameter heavy-duty line. The thicker line has the heft to chop through tougher materials, while the thin- ner line provides a more precise cut. - Page 11 WARNING THROWN OBJECT HAZARD! • Objects such as rocks, pebbles, and small debris will be thrown violently by the cutting head, resulting in sig- nificant hazard to eyes and exposed body parts. • Always wear safety-approved eye pro- tection and suitable clothing and footwear.
-
Page 12: Section 5: Maintenance
Section WARNING Before inspecting, cleaning or servicing the machine, shut off engine, discon- nect spark plug wire, and make sure that all moving parts have come to a com- plete stop. Remove ignition key on electric start models. Failure to follow these instructions can result in personal injury or property damage. -
Page 13: Removing And Replacing The Trimmer Head
WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage. Figure 5-2: Belt tension adjustment. - Page 14 Section 5: Maintenance WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models.
-
Page 15: Lubrication
WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage. Figure 5-6A 10. -
Page 16: Spark Plug Service
Section 5: Maintenance WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. - Page 17 WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage. CHANGING TRIMMER LINES When trimmer lines wear, it takes longer to complete mowing and trimming pro-...
-
Page 18: Troubleshooting
Section 5: Maintenance WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. -
Page 19: Parts List
Model 52067 PARTS LIST – DRAWING NO. 1 Ref. # Part # Description 1917765 Debris Guard ... 1 1918116 Decal-Logo ... 1 1915290 Push-in Fastener... 5 1917407001 Debris Guard Support... 1 1754128 Hex Flange Screw, 1/4-20 x 3/4 ... 8 1915320 Spacer ... - Page 20 Parts List See DRAWING NO. 1 DRAWING NO. 2 See ACCESSORIES AND KITS Model 52067 See DRAWING NO. 3...
- Page 21 Model 52067 Ref. # Part # Description 1917592 Wheel/Tire Assembly... 1917593 Locking Retaining Ring ... 1917775 Flat Washer ... 1917258 Axle ... 1724491 Self-Tap Screw, 5/16-18 x 3/4 ... 1918069 Self-Tap Screw, 5/16-18 x 2... 1917588 Cap Plug... 1734514 Hex Lock Nut, 1/2-13 ... 9928 Belleville Washer ...
- Page 22 Parts List DRAWING NO. 3 PARTS LIST – DRAWING NO. 3 Ref. # Part # 1918283 1915889 1918304 1918070001 1917589 1908677 1749977001 1983658 1185814 1918081 1100807 1110106 1763682 1100799 1917145001 1732499 Model 52067 Description Qty. Upper Handlebar (Incl. Refs. 2 & 3) ... Decal–Bail Engage/Disengage ...
- Page 23 Model 52067 Ref. # N/I Not included with unit, order separately ACCESSORIES AND KITS Part # Description 1904476 Trimmer String Kit, .155" dia. line (includes 24 pieces)... N/I 1904477 Trimmer String Kit, .130" dia. line (includes 24 pieces)... N/I Parts List Qty.
-
Page 24: Customer Service Information
CUSTOMER SERVICE INFORMATION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory so that we can provide you with warranty benefits and in- formational bulletins.