Table of Contents
Advertisement
Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR'S MANUAL
* Model 24AF572B766 Shown
Log Splitter — Model Series 570
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
FORM NO. 769-00088E
PRINTED IN U.S.A
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
4/25/2006
Advertisement
Table of Contents
Related Manuals for Troy-Bilt 570 Series
Summary of Contents for Troy-Bilt 570 Series
- Page 1 Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty OPERATOR’S MANUAL * Model 24AF572B766 Shown Log Splitter — Model Series 570 IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush- covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
-
Page 2: Table Of Contents
This information will be necessary to use the web site or obtain assistance from our Customer Support Department or your Troy-Bilt service dealer. Please do NOT return the unit to the retailer from which it was purchased, without first contacting Customer Support. -
Page 3: Safety Labels
Safety Labels Found On Your Log Splitter ������� ������ ����������� ��� �� �������� ���� �� ���� ������ ��� �������� ������� ������ ���� ����� ���� ���� ����� ��� ������ ������ �������� ���������� �� ����� ��� �������� �� ���� ��� ����� ������� ��������... -
Page 4: Safe Operation Practices
DANGER: This machine was built to be operated according to the rules for safe operation in this Safe manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Operation Failure to observe the following safety instructions could result in serious injury or death. -
Page 5: Maintenance And Storage
f. Never overfill the fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion. g. Replace gasoline cap and tighten securely. h. If gasoline is spilled, wipe it off the engine and equipment. -
Page 6: Setting Up Your Log Splitter
Setting Up Your Log Splitter WARNING Use extreme cau- tion unpacking this machine. Some components are very heavy and will require additional people or mechanical handling equipment. NOTE: All references in this manual to the left or right side of the log splitter is from the operating position only. - Page 7 3. Disconnect the log cradle from the beam on the side of the control valve. See Figure 3-5. 4. Lift and slide the cylinder up to the top of beam and into the weld brackets. See Figure 3-6. 5. Attach the dislodger over the wedge assembly and secure with hardware, previously removed, to the weld brackets.
-
Page 8: Operating Your Log Splitter
Operating Your Log Splitter WARNING Jack Stand IMPORTANT Your log splitter is shipped with motor oil in the engine. However, you MUST check the oil level before operat- ing. Be careful not to overfill. Beam Locks These two locks, as their name suggests, are used to secure the beam in the horizontal or the vertical position. - Page 9 Control Handle The control handle has three positions. See Figure 4-2. • FORWARD: Move control handle FORWARD or DOWN to move wedge to split wood. NOTE: Control handle will return to neutral position as soon as handle is released.(Forward Position only) •...
-
Page 10: Log Dislodger
Operating Your Log Splitter WARNING Never remove partially split wood from the Before Each Use wedge with your 1. Remove the dipstick and check hydraulic fluid level. hands. Fingers may be- Refill if necessary. Approved fluids include Dexron® III / Mercon® III automatic transmission fluid, a come trapped between 10 Weight AW hydraulic oil or Pro-Mix™... - Page 11 6. Use a flexible “spider” type coupling between engine and pump drive shafts. 7. Keep hoses clear and unblocked. 8. Bleed air out of hoses before operating. 9. Flush and clean hydraulic system before restarting after servicing. 10.Use “pipe dope” on all hydraulic fittings. 11.
-
Page 12: Maintaining Your Log Splitter
Adjustment Maintaining Bolt Your Log Splitter WARNING Do not at any time make any adjustments without first stopping engine, disconnecting spark plug wire, and grounding it against Wedge Assembly Adjustment the engine. Always As normal wear occurs and there is excessive “play” wear safety glasses between the wedge and beam, adjust the bolts on the during operation or... - Page 13 Hydraulic Fluid and Inlet Filter • Check the hydraulic fluid level in the log splitter reservoir tank before each use. Maintain fluid level within the range specified on the dipstick at all times. • Change the hydraulic fluid in the reservoir every 100 hours of operation.
- Page 14 Maintaining Your Log Splitter 1. Remove three nuts that secure the pump to the coupling shield. Two nuts are at the bottom corners WARNING and one is in the top center. See Figure 5-3. 2. Remove the pump. 3. Rotate the engine by slowly pulling starter handle Excessive pressure until engine coupling half set screw is visible.
-
Page 15: Storing Your Log Splitter
Storing Your Log Splitter Prepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 days or more. WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources are present such as hot water and space... -
Page 16: Troubleshooting
Problem Engine fails to start Trouble Shooting Engine runs erratic For repairs beyond the minor adjust- ments listed here, contact an authorized service dealer. Engine Overheats Hydraulic Problem Cylinder rod will not Trouble Shooting Cause 1. Spark plug wire disconnected. 2. - Page 17 Problem Slow cylinder shaft 1. Gear sections damaged. speed while extending 2. Excessive pump inlet vacuum. and retracting. 3. Slow engine speed. 4. Damaged relief valve. 5. Incorrect oil level. 6. Contaminated oil. 7. Directional valve leaking internally. 8. Internally damaged cylinder. 1.
-
Page 18: Illustrated Parts List
Model Series 570 To secure ground wire... -
Page 19: Parts List
718-0769A Hydraulic Cylinder 727-0634 Hydraulic Tube 710-1018 Hex Cap Screw 1/2-20 x 2.75 737-0192 90 Degree Solid Adapter 718-0481A Control Valve 737-0153 Return Elbow 737-0238 Nipple Pipe 1/2-14 710-1806 Hex Cap Screw 1/2-13 x 3.25 719-0550A Wedge Assembly 10. 712-3058 Hex Lock Nut, 1/2-20 11. - Page 20 MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/or its territories and possessions (either entity respectively, “Troy-Bilt”).