Table of Contents
Advertisement
Owner's Manual
SMARTONLINE
™
1111 W. 35th Street
Rack/Tower Mount
Chicago, IL 60609 USA
Customer Support: (773) 869-1234
Online UPS Systems
www.tripplite.com
ESPAÑOL: p. 13
U L
C
US
FRANÇAIS: p. 25
DEUTSCH: p. 37
Important Safety Instructions:
p. 2
Installation:
p. 3 - 5
Basic Operation:
p. 6 - 9
Battery Replacement:
p. 10
Storage & Service:
p. 11
Specifications:
p. 11 - 12
Copyright ©2001 Tripp Lite. All rights reserved. SmartOnline ™ is a trademark of Tripp Lite.
Advertisement
Table of Contents
Related Manuals for Tripp Lite SmartOnline SU1000RT2UHV
Summary of Contents for Tripp Lite SmartOnline SU1000RT2UHV
- Page 1 Installation: p. 3 - 5 Basic Operation: p. 6 - 9 Battery Replacement: p. 10 Storage & Service: p. 11 Specifications: p. 11 - 12 Copyright ©2001 Tripp Lite. All rights reserved. SmartOnline ™ is a trademark of Tripp Lite.
-
Page 2: Important Safety Instructions
Equipment Connection Warning • Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or failure of a Tripp Lite UPS System could cause failure or significantly alter the performance of a life-support device. -
Page 3: Installation
Installation Mounting Rackmount 1) Loosen the wingnuts on each of the two UPS Side Supports; adjust the length of the supports to match the depth of your rack; tighten wingnuts. 2) Mount both UPS Side Supports in your rack on the inside surfaces of the rack rails. -
Page 4: Connection & Start-Up
Connection & Start-Up Plug your UPS's Line Cord into an electrical outlet. If your model features a detachable line cord, first plug the female end into your UPS’s AC Input Receptacle. Your UPS must be connected to a dedicated circuit of sufficient amperage—check the “Recommended Utility Amps”... -
Page 5: Optional Connections
Serial Port Connection Using the serial cable provided, connect a seri- al port on your computer to the serial port of your UPS. Install Tripp Lite's PowerAlert soft- ware (provided on CD) on the computer . SU2200RT2U Shown External Battery Pack... -
Page 6: Basic Operation
Basic Operation Front Panel Switches “ON/TEST” Switch: This switch controls four separate UPS functions: UPS Power ON To turn the UPS on, press this switch, hold it for several seconds until you hear a beep, then release it. The “ON LINE” LED will illuminate. UPS Self-Test During normal on-line operation, press this switch and hold it until you hear a beep. - Page 7 AC mains power, but will not receive battery power during a blackout. In this case, contact Tripp Lite for service. “FAULT” LED (Select Models Only): This red light will flash when your UPS detects an internal fault (overheating, overvoltages, etc.) or...
-
Page 8: Rear Panel
“SMART” Serial Port: This serial port connects your UPS to any work- station or server. Use with Tripp Lite software and cabling to monitor and manage network power and automatically save open files and shut down equipment during a blackout. The port uses RS-232 communi- cations to transmit UPS and power conditions. - Page 9 Rear Panel (Continued) Output Circuit Breakers Switches (Select Models Only): These reset- table circuit breakers protect your UPS from output overload. If one or both breakers trip, remove some of the load on the circuit(s) and allow the UPS to cool before pressing the breaker switch(es) in to reset.
-
Page 10: Battery Replacement
Battery Replacement Under normal conditions, the original battery in your UPS will last several years. Contact Tripp Lite for information about replacement batteries. Battery replacement should be performed only by qualified service personnel. The batteries are hot-swappable: it is not necessary to turn off or disconnect the UPS and its connected load to replace the UPS’s batteries. -
Page 11: Storage And Service
Service If returning your UPS to Tripp Lite, please carefully pack the UPS using the ORIG- INAL PACKING MATERIAL that came with the unit. Enclose a letter describing the symptoms of the problem. If the UPS is within the 2 year warranty period, enclose a copy of your sales receipt. - Page 12 Specifications (Continued) Model Input Voltage: Input Breaker Rating: Input Plug Type: Recommended Utility Amps: Output Capacity (VA/Watts): Battery Runtime (Half Load/Full Load) Min.: System Battery Voltage: Approvals: Model Input Voltage: Input Breaker Rating: Input Plug Type: Recommended Utility Amps: Output Capacity (VA/Watts): Battery Runtime (Half Load/Full Load) Min.: System Battery Voltage: Approvals:...